This website uses cookies. By clicking Accept, you consent to the use of cookies. Click Here to learn more about how we use cookies.
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Extreme Networks
- Community List
- Switching & Routing
- ExtremeSwitching (EOS)
- RE: LAG X690 between SFP and UTP
Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
LAG X690 between SFP and UTP
LAG X690 between SFP and UTP
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
03-05-2018 08:40 PM
Hello i have a Stack between two switch model X690 one of then 10G fiber an other of copper switch. But when i make a lag show the following error. It is possible to make a lag between 10G copper +10 G fibber?
=========================
XXXXXXXXX # show ports 1:48,3:48 configuration no-refresh
Port Configuration
Port Virtual Port Link Auto Speed Duplex Flow Load Media
router State State Neg Cfg Actual Cfg Actual Cntrl Master Pri Red
================================================================================
1:48 VR-Default E R OFF 10000 FULL NONE
3:48 VR-Default E A ON 10000 10000 FULL FULL SYM 3:48 UTP
================================================================================
XXXXXXXX# configure sharing 3:48 add ports 1:48
Error: Member Port 1:48 has Auto Negotiation Off while Master Port has Auto Negotiation On
Configuration failed on backup Node, command execution aborted!
===================================================
=========================
XXXXXXXXX # show ports 1:48,3:48 configuration no-refresh
Port Configuration
Port Virtual Port Link Auto Speed Duplex Flow Load Media
router State State Neg Cfg Actual Cfg Actual Cntrl Master Pri Red
================================================================================
1:48 VR-Default E R OFF 10000 FULL NONE
3:48 VR-Default E A ON 10000 10000 FULL FULL SYM 3:48 UTP
================================================================================
XXXXXXXX# configure sharing 3:48 add ports 1:48
Error: Member Port 1:48 has Auto Negotiation Off while Master Port has Auto Negotiation On
Configuration failed on backup Node, command execution aborted!
===================================================
12 REPLIES 12
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
03-06-2018 01:18 PM
Hello i also tried to setup 3:48 to auto OFF but it not supported the following error says:
==============
XXXXXXX # configure ports 3:48 auto off speed 10000 duplex full
Error: Auto negotiation off is not supported on port 3:48 at 10 Gbps speed.
Configuration failed on backup Node, command execution aborted!
* XXXXXX #
==============
XXXXXXX # configure ports 3:48 auto off speed 10000 duplex full
Error: Auto negotiation off is not supported on port 3:48 at 10 Gbps speed.
Configuration failed on backup Node, command execution aborted!
* XXXXXX #
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
03-06-2018 09:10 AM
Hello i cant change the auto neg in 1:48, Is the first that i have tried ...
======================
********** # configure ports 1:48 auto on speed 10000 duplex full
Error: Auto negotiation is not supported on port 1:48 at 10G speed
Configuration failed on backup Node, command execution aborted!
*********
Also i have a LAG between to 10G UTP ports and works perfect, only fails when i add to the sharing group the 10G fiber port.
======================
********** # configure ports 1:48 auto on speed 10000 duplex full
Error: Auto negotiation is not supported on port 1:48 at 10G speed
Configuration failed on backup Node, command execution aborted!
*********
Also i have a LAG between to 10G UTP ports and works perfect, only fails when i add to the sharing group the 10G fiber port.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
03-06-2018 09:10 AM
No steven All sfp are 10Gb . Why ?
Port Configuration
Port Virtual Port Link Auto Speed Duplex Flow Load Media
router State State Neg Cfg Actual Cfg Actual Cntrl Master Pri Red
================================================================================
1:1 VR-Default E R OFF 10000 FULL SF+_SR
1:2 VR-Default E R OFF 10000 FULL SF+_SR
1:3 VR-Default E R OFF 10000 FULL SF+_SR
1:4 VR-Default E R OFF 10000 FULL SF+_SR
1:5 VR-Default E R OFF 10000 FULL SF+_SR
1:6 VR-Default E R OFF 10000 FULL SF+_SR
1:7 VR-Default E R OFF 10000 FULL NONE
1:8 VR-Default E R OFF 10000 FULL SF+_SR
Port Configuration
Port Virtual Port Link Auto Speed Duplex Flow Load Media
router State State Neg Cfg Actual Cfg Actual Cntrl Master Pri Red
================================================================================
1:1 VR-Default E R OFF 10000 FULL SF+_SR
1:2 VR-Default E R OFF 10000 FULL SF+_SR
1:3 VR-Default E R OFF 10000 FULL SF+_SR
1:4 VR-Default E R OFF 10000 FULL SF+_SR
1:5 VR-Default E R OFF 10000 FULL SF+_SR
1:6 VR-Default E R OFF 10000 FULL SF+_SR
1:7 VR-Default E R OFF 10000 FULL NONE
1:8 VR-Default E R OFF 10000 FULL SF+_SR
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
03-06-2018 09:10 AM
Is there any 1G SFP had been installed on the switch?
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
03-06-2018 05:55 AM
The error indicates that one link has auto negotiation on, the other off. Tun on auto negotiation on on both 10Gbit links.
