Different Rev on stack
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-13-2016 04:46 PM
I have a stack of x450e switches and I recently updated the XOS. When I do a Show Version it shows the two slots with different Rev #'s. Rev 10 is the correct version but slot 2 shows Rev 7. Also, the BootROM is different. Is that normal, and if not what do I need to do to correct this issue?
Slot-1 Extreme-Core.1 # show verSlot-1 : 800190-00-10 0748G-80067 Rev 10.0 BootROM: 1.0.5.7 IMG: 15.3.5. 2
Slot-2 : 800190-00-07 0814G-80299 Rev 7.0 BootROM: 1.0.3.5 IMG: 15.3.5.2
Slot-3 :
Slot-4 :
Slot-5 :
Slot-6 :
Slot-7 :
Slot-8 :
Image : ExtremeXOS version 15.3.5.2 v1535b2-patch1-10 by release-manager
on Fri Apr 8 11:48:36 EDT 2016
BootROM : 1.0.5.7
Diagnostics : 5.10
Slot-1 Extreme-Core.1 # show verSlot-1 : 800190-00-10 0748G-80067 Rev 10.0 BootROM: 1.0.5.7 IMG: 15.3.5. 2
Slot-2 : 800190-00-07 0814G-80299 Rev 7.0 BootROM: 1.0.3.5 IMG: 15.3.5.2
Slot-3 :
Slot-4 :
Slot-5 :
Slot-6 :
Slot-7 :
Slot-8 :
Image : ExtremeXOS version 15.3.5.2 v1535b2-patch1-10 by release-manager
on Fri Apr 8 11:48:36 EDT 2016
BootROM : 1.0.5.7
Diagnostics : 5.10
7 REPLIES 7
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-13-2016 05:13 PM
Hi Andrew,
BootROM 1.0.5.7, which is currently installed on slot 1 of the 2-node stack is the latest BootROM for the X450e switches. Since you have a 2-node stack of the same type, to avoid any unexpected side effects in case of a stack node failure/failover you can consider upgrading slot 2 to a matching BootROM as Slot 1, and then reboot Slot 2 for the BootROM update to take effect (ideally during a short maintenance window).
Thank you.
Best regards,
Andrew
BootROM 1.0.5.7, which is currently installed on slot 1 of the 2-node stack is the latest BootROM for the X450e switches. Since you have a 2-node stack of the same type, to avoid any unexpected side effects in case of a stack node failure/failover you can consider upgrading slot 2 to a matching BootROM as Slot 1, and then reboot Slot 2 for the BootROM update to take effect (ideally during a short maintenance window).
Thank you.
Best regards,
Andrew
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-13-2016 05:05 PM
Yes, everything is working normally, I was just concerned when I seen the difference and wanted to make sure that was all normal.
Thanks again for the quick response.
Thanks again for the quick response.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-13-2016 04:58 PM
Generally we don't recommend a customer to upgrade or change the bootrom version unless there's a reason to do so. Is everything working normally?
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-13-2016 04:56 PM
Thanks for the reply. So, the Rev # is normal, would that be true for the BootROM as well?
I also did a show slot detail and that all looks correct.
Slot-1 Extreme-Core.7 # show slot detail
Slot-1 information:
State: Operational
Download %: 100
Restart count: 0 (limit 5)
Serial number: 800190-00-10 0748G-80067
Hw Module Type: X450e-48p
SW Version: 15.3.5.2
SW Build: v1535b2-patch1-10
Configured Type: X450e-48p
Ports available: 50
Recovery Mode: Reset
Node MAC: 02:04:96:34:8F:84
Current State: MASTER
Image Selected: primary
Image Booted: primary
Primary ver: 15.3.5.2
Secondary ver: 15.3.5.2
Config Selected: primary.cfg
Slot-2 information:
State: Operational
Download %: 100
Restart count: 0 (limit 5)
Serial number: 800190-00-07 0814G-80299
Hw Module Type: X450e-48p
SW Version: 15.3.5.2
SW Build: v1535b2-patch1-10
Configured Type: X450e-48p
Ports available: 50
Recovery Mode: Reset
Node MAC: 02:04:96:34:8F:84
Current State: BACKUP (In Sync)
Image Selected: primary
Image Booted: primary
Primary ver: 15.3.5.2
Secondary ver: 15.3.5.2
Config Selected: primary.cfg
I also did a show slot detail and that all looks correct.
Slot-1 Extreme-Core.7 # show slot detail
Slot-1 information:
State: Operational
Download %: 100
Restart count: 0 (limit 5)
Serial number: 800190-00-10 0748G-80067
Hw Module Type: X450e-48p
SW Version: 15.3.5.2
SW Build: v1535b2-patch1-10
Configured Type: X450e-48p
Ports available: 50
Recovery Mode: Reset
Node MAC: 02:04:96:34:8F:84
Current State: MASTER
Image Selected: primary
Image Booted: primary
Primary ver: 15.3.5.2
Secondary ver: 15.3.5.2
Config Selected: primary.cfg
Slot-2 information:
State: Operational
Download %: 100
Restart count: 0 (limit 5)
Serial number: 800190-00-07 0814G-80299
Hw Module Type: X450e-48p
SW Version: 15.3.5.2
SW Build: v1535b2-patch1-10
Configured Type: X450e-48p
Ports available: 50
Recovery Mode: Reset
Node MAC: 02:04:96:34:8F:84
Current State: BACKUP (In Sync)
Image Selected: primary
Image Booted: primary
Primary ver: 15.3.5.2
Secondary ver: 15.3.5.2
Config Selected: primary.cfg
