How to reduce/load balance Bandwidth utilization on a Single Link between two Core Switch.

[Paul11]

Hi, Please advice on How to reduce/load balance Bandwidth utilization on a Single Link between two Core Switch?

[Paul11]

Even after i enable Lacp .. port is not sharing. Utilization is high on Link 1 only. I want to use load balance on both links. Please kindly see the below output and advice thanks.

* I try L2 static, L3_L4 and LACP. all the same ports are not load balance. *

enable sharing 1 grouping 1,4

enable sharing 1 grouping 1,4 L3_L4

enable sharing 1 grouping 1,4 algorithm address-based L3_L4 lacp


CoreSW # sh port 1,4 utilization bandwithPort Link Link Rx Peak Rx Tx Peak Tx
State Speed % bandwidth % bandwidth % bandwidth % bandwidth
================================================================================
Link_1> A 1000 82.06 94.94 48.23 55.72
Link_2> A 1000 0.25 0.30 1.34 1.57
================================================================================
> indicates Port Display Name truncated past 8 characters
Link State: A-Active, R-Ready, NP-Port Not Present, L-Loopback

CoreSW #sh sharing
Load Sharing Monitor
Config Current Agg Ld Share Ld Share Agg Link Link Up
Master Master Control Algorithm Group Mbr State Transitions
==============================================================================
1 1 LACP L3_L4 1 Y A 0
L3_L4 4 Y A 0
==============================================================================
Link State: A-Active, D-Disabled, R-Ready, NP-Port not present, L-Loopback
Load Sharing Algorithm: (L2) Layer 2 address based
(L3_L4) Layer 3 address and Layer 4 port based
Number of load sharing trunks: 1

Please kindly advice. Thanks.

[PARTHIBAN_CHINN]

In show sharing you must see all the ports in lag.
could you check the configuration.
on both the switches.
enable sharing 1 grouping 1,2 algorithm address-based l2

[PARTHIBAN_CHINN]

write an acl to drop unnecessary multicast trafic sent from host.
Are you using Mlag,STP ,RSTP,ESRP?
Any of the above protocols there are better options.
is this a triangular toplogy.

[Paul11]

Thanks Ravisekar,

Even after i enable Lacp .. port is not sharing. Utilization is high on Link 1 only. I want to use load balance on both links. Please kindly see the below output and advice thanks.

* I try L2 static, L3_L4 and LACP. all the same ports are not load balance. *

enable sharing 1 grouping 1,4

enable sharing 1 grouping 1,4 L3_L4

enable sharing 1 grouping 1,4 algorithm address-based L3_L4 lacp


CoreSW # sh port 1,4 utilization bandwithPort Link Link Rx Peak Rx Tx Peak Tx
State Speed % bandwidth % bandwidth % bandwidth % bandwidth
================================================================================
Link_1> A 1000 82.06 94.94 48.23 55.72
Link_2> A 1000 0.25 0.30 1.34 1.57
================================================================================
> indicates Port Display Name truncated past 8 characters
Link State: A-Active, R-Ready, NP-Port Not Present, L-Loopback

CoreSW #sh sharing
Load Sharing Monitor
Config Current Agg Ld Share Ld Share Agg Link Link Up
Master Master Control Algorithm Group Mbr State Transitions
==============================================================================
1 1 LACP L3_L4 1 Y A 0
L3_L4 4 Y A 0
==============================================================================
Link State: A-Active, D-Disabled, R-Ready, NP-Port not present, L-Loopback
Load Sharing Algorithm: (L2) Layer 2 address based
(L3_L4) Layer 3 address and Layer 4 port based
Number of load sharing trunks: 1

Please kindly advice. Thanks.