Module in Slot-2 is removed, X460 stacks keep failing.
Anonymous
Not applicable
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎03-12-2015 06:28 PM
Hi everybody,
I need to know If there is any CLI command (or NetSight Applications tool) I can use to check a Securestack C3 switch for HW issues.
I tried the various "show port ..." commands, but they only show if ports are admin and operationally up or down, whereas I need to run some hardware diagnostics to check if some ports are really working or not.
Thank you in advance for your replies!
I need to know If there is any CLI command (or NetSight Applications tool) I can use to check a Securestack C3 switch for HW issues.
I tried the various "show port ..." commands, but they only show if ports are admin and operationally up or down, whereas I need to run some hardware diagnostics to check if some ports are really working or not.
Thank you in advance for your replies!
8 REPLIES 8
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎03-12-2015 08:04 PM
Martin,
So you are on 15.6 now? Have you opened a case with TAC on this yet?
Bill
So you are on 15.6 now? Have you opened a case with TAC on this yet?
Bill
Anonymous
Not applicable
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎03-12-2015 07:57 PM
Hi Bill,
Sorry, forgot to answer your other question. These have been in service since the weekend and have been experiencing problems since then.
Before there was a mixture of x460 and 400's, but none of them stacked. Was running a mixture of Extremeware and EXOS, but as I said, no stacking.
From a logical level the design now looks like a single link end to end using stacking and lags, so there is no spanning tree configured.
Many thanks,
Martin
Sorry, forgot to answer your other question. These have been in service since the weekend and have been experiencing problems since then.
Before there was a mixture of x460 and 400's, but none of them stacked. Was running a mixture of Extremeware and EXOS, but as I said, no stacking.
From a logical level the design now looks like a single link end to end using stacking and lags, so there is no spanning tree configured.
Many thanks,
Martin
Anonymous
Not applicable
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎03-12-2015 07:42 PM
Hi Bill,
I don't have a current show version and show switch as I'm not currently on site but can update tomorrow but below is what they where before we upgraded them to 15.6.2.
The commands taken before upgrade are as follows:
-> show version
Switch : 800538-00-02 1336N-42383 Rev 2.0 BootROM: 2.0.1.7 IMG: 12.5.4.5
SS-B-1 : 800384-00-01 1404N-40552 Rev 1.0
PSU-1 : NONE NONE NONE Rev 0.0
PSU-2 : EDPS-300AB A-S9 800515-00-03 1339E-40304 Rev 0.0
Image : ExtremeXOS version 12.5.4.5 v1254b5 by release-manager
on Tue Jun 28 10:10:40 PDT 2011
BootROM : 2.0.1.7
Diagnostics : 2.10
-> show switch
SysName: X460-48t
SysLocation:
SysContact: support@extremenetworks.com, +1 888 257 3000
System MAC: 00:04:96:8B:E8:3B
System Type: X460-48t
SysHealth check: Enabled (Normal)
Recovery Mode: All
System Watchdog: Enabled
Current Time: Wed Feb 18 22:18:55 2015
Timezone: [Auto DST Disabled] GMT Offset: 0 minutes, name is UTC.
Boot Time: Wed Feb 18 22:04:36 2015
Boot Count: 16
Next Reboot: None scheduled
System UpTime: 14 minutes 19 seconds
Current State: OPERATIONAL
Image Selected: primary
Image Booted: primary
Primary ver: 12.5.4.5
Secondary ver: 12.5.4.5
Config Selected: NONE
Config Booted: Factory Default
Many thanks.
I don't have a current show version and show switch as I'm not currently on site but can update tomorrow but below is what they where before we upgraded them to 15.6.2.
The commands taken before upgrade are as follows:
-> show version
Switch : 800538-00-02 1336N-42383 Rev 2.0 BootROM: 2.0.1.7 IMG: 12.5.4.5
SS-B-1 : 800384-00-01 1404N-40552 Rev 1.0
PSU-1 : NONE NONE NONE Rev 0.0
PSU-2 : EDPS-300AB A-S9 800515-00-03 1339E-40304 Rev 0.0
Image : ExtremeXOS version 12.5.4.5 v1254b5 by release-manager
on Tue Jun 28 10:10:40 PDT 2011
BootROM : 2.0.1.7
Diagnostics : 2.10
-> show switch
SysName: X460-48t
SysLocation:
SysContact: support@extremenetworks.com, +1 888 257 3000
System MAC: 00:04:96:8B:E8:3B
System Type: X460-48t
SysHealth check: Enabled (Normal)
Recovery Mode: All
System Watchdog: Enabled
Current Time: Wed Feb 18 22:18:55 2015
Timezone: [Auto DST Disabled] GMT Offset: 0 minutes, name is UTC.
Boot Time: Wed Feb 18 22:04:36 2015
Boot Count: 16
Next Reboot: None scheduled
System UpTime: 14 minutes 19 seconds
Current State: OPERATIONAL
Image Selected: primary
Image Booted: primary
Primary ver: 12.5.4.5
Secondary ver: 12.5.4.5
Config Selected: NONE
Config Booted: Factory Default
Many thanks.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎03-12-2015 07:17 PM
Martin,
First, what version of code and can you send me the output of "show switch" and "show ver" ??
How long have these been in service?
Bill
First, what version of code and can you send me the output of "show switch" and "show ver" ??
How long have these been in service?
Bill
