Network fell down and removed a vr?

[Petteri_Oksanen]

So I had this network which topology is this:

And I had OSPF up and running and everything seemed to be well. I fired up a windows 7 32-bit host machine under Switch1, enabled port 2, added vlan to it as untagged and suddenly Switch1 gave this error:

I shut down the host and rebooted everything, and everything was fine. I fired up host once again and this same error occurred in under one minute. I rebooted everything once again and took the host down so the situation would calm down.

Now I noticed in Router1 had my VR and vlan "internet" removed?? I had "vr-corporation" and everything under it. Both default vlan and vr-default were "disabled". Now I watch Router1 configs and everything is preserved but vlan "internet" and vr "vr-corporation" has completely vanished. I tried to load my configurations again but they did not appear.

Now I tried to load the configurations again and it only says:
"This command cannot be executed during configuration load."

What is happening??

[Petteri_Oksanen]

Would like to know why this thread has been marked as "Solved"?

The problem still consists.

[Petteri_Oksanen]

Thanks. This evil HAL is taking over me  last night while I was making configs it told me to give up.
I am using VirtualBox v4.3.26 r98988 with extension pack (aka the latest one).
The problem can also be in the host itself, since without it everything works well. I will try with other kinds of hosts also.

[Stephane_Grosj1]

At first look, I don't see an obvious issue in your config. Remember that this is VM, so there's no dataplane, it's (partially) emulated through software. The process crashing is HAL, and while we could see a correlation here with 2001 a space odyssey in the sense it's hurting you, this is the Hardware Abstraction Layer. So maybe a small hint.

I'll try to find time to check your config on my VM setup.

But I have already ran many VM with user created VR, MPLS, BGP and OSPF running in it without issues.

What version of VirtualBox do you have?

[Petteri_Oksanen]

I did the configurations again and here they are:

Router1
configure vlan default delete ports all
configure vr VR-Default delete ports 1-3
create vr "vr-corporation"
configure vr vr-corporation add ports 1-3
configure vlan default delete ports 1-3
create vlan "internet" vr vr-corporation
configure vlan internet tag 42
configure vlan "internet" qosprofile QP1
create vlan "r_kerros_1" vr vr-corporation
configure vlan r_kerros_1 tag 11
configure vlan "r_kerros_1" qosprofile QP1
create vlan "r_kerros_2" vr vr-corporation
configure vlan r_kerros_2 tag 12
configure vlan "r_kerros_2" qosprofile QP1
configure vlan internet add ports 3 tagged
configure vlan r_kerros_1 add ports 1 tagged
configure vlan r_kerros_2 add ports 2 tagged
configure vlan Mgmt ipaddress 192.168.56.100 255.255.255.0
configure vlan internet ipaddress 10.10.10.10 255.255.255.0
enable ipforwarding vlan internet
configure vlan r_kerros_1 ipaddress 192.168.10.1 255.255.255.0
enable ipforwarding vlan r_kerros_1
configure vlan r_kerros_2 ipaddress 192.168.20.1 255.255.255.0
enable ipforwarding vlan r_kerros_2
configure vr vr-corporation add protocol ospf

#
# Module ospf configuration on virtual router vr-corporation.
#
virtual-router vr-corporation
configure ospf routerid 1.1.1.1
enable ospf
create ospf area 1.2.3.4
configure ospf add vlan internet area 1.2.3.4 link-type point-to-point
configure ospf add vlan r_kerros_1 area 1.2.3.4 link-type point-to-point
configure ospf add vlan r_kerros_2 area 1.2.3.4 link-type point-to-point
virtual-router VR-Default

---------------------------------------------------------

Switch1
configure vlan default delete ports all
configure vr VR-Default delete ports 1-5
create vr "vr-corporation"
configure vr vr-corporation add ports 1-2
configure vlan default delete ports 1-5
create vlan "kerros_1" vr vr-corporation
configure vlan kerros_1 tag 11
configure vlan "kerros_1" qosprofile QP1
disable port 2
disable port 3
disable port 4
disable port 5
configure vlan kerros_1 add ports 1 tagged
configure vlan kerros_1 add ports 2 untagged
configure vlan Mgmt ipaddress 192.168.56.101 255.255.255.0
configure vlan kerros_1 ipaddress 192.168.10.2 255.255.255.0
enable ipforwarding vlan kerros_1
configure vr vr-corporation add protocol ospf

#
# Module ospf configuration on virtual router vr-corporation.
#
virtual-router vr-corporation
configure ospf routerid 2.2.2.2
enable ospf
create ospf area 1.2.3.4
configure ospf add vlan kerros_1 area 1.2.3.4 link-type point-to-point
virtual-router VR-Default

---------------------------------------------------------

Switch2
configure vlan default delete ports all
configure vr VR-Default delete ports 1-5
create vr "vr-corporation"
configure vr vr-corporation add ports 1-2
configure vlan default delete ports 1-5
create vlan "kerros_2" vr vr-corporation
configure vlan kerros_2 tag 12
disable port 2
disable port 3
disable port 4
configure vlan kerros_2 add ports 1 tagged
configure vlan Mgmt ipaddress 192.168.56.102 255.255.255.0
configure vlan kerros_2 ipaddress 192.168.20.2 255.255.255.0
enable ipforwarding vlan kerros_2
configure vr vr-corporation add protocol ospf

#
# Module ospf configuration on virtual router vr-corporation.
#
virtual-router vr-corporation
configure ospf routerid 3.3.3.3
enable ospf
create ospf area 1.2.3.4
configure ospf add vlan kerros_2 area 1.2.3.4 link-type point-to-point
virtual-router VR-Default

---------------------------------------------------------

.. I tried again to open the host (win7 with ip 192.168.10.5/24) and it all fell down again. Is there anyone who can make any sense in this? Have I added the ports correctly?

Thanks

edit: I have purposely disabled the port on switch1 to prevent the crash. Port 2 has the host attached in it.