cancel
Showing results forĀ 
Search instead forĀ 
Did you mean:Ā 

New Vlan on our main switch but cannot use any of the IP addresses in that Vlan

New Vlan on our main switch but cannot use any of the IP addresses in that Vlan

Beth_Dierks
New Contributor
I have created a new Vlan on our main switch and can ping the Vlan's gateway from all areas but if we try to use an IP address from that Vlan it will not work. Any ideas on what needs to be fixed?
16 REPLIES 16

Beth_Dierks
New Contributor
If I ping a device that is currently configured to 116.2 I get nothing back even on the switch:

Ping(ICMP) 10.128.116.2: 4 packets, 8 data bytes, interval 1 second(s).

--- 10.128.116.2 ping statistics ---
4 packets transmitted, 0 packets received, 100% loss
round-trip min/avg/max = 0/0/0 ms
Slot-1 Main-96.7 # ping 10.128.116.1
Ping(ICMP) 10.128.116.1: 4 packets, 8 data bytes, interval 1 second(s).
16 bytes from 10.128.116.1: icmp_seq=0 ttl=64 time=0.211 ms
16 bytes from 10.128.116.1: icmp_seq=1 ttl=64 time=0.085 ms
16 bytes from 10.128.116.1: icmp_seq=2 ttl=64 time=0.089 ms
16 bytes from 10.128.116.1: icmp_seq=3 ttl=64 time=0.086 ms

Patrick_Voss
Extreme Employee
What IP address are you trying to ping?

Beth_Dierks
New Contributor
Here is the Show Iproute:

Ori Destination Gateway Mtr Flags VLAN Duration
#s Default Route 10.128.211.11 1 UG---S-um--f- v211 532d:3h:42m:46s
#d 10.128.0.0/22 10.128.0.1 1 U------um--f- v113 532d:3h:42m:55s
#d 10.128.8.0/21 10.128.8.1 1 U------um--f- v50 532d:3h:42m:56s
#d 10.128.100.0/24 10.128.100.1 1 U------um--f- v100 532d:3h:42m:56s
#d 10.128.101.0/24 10.128.101.1 1 U------um--f- v101 532d:3h:42m:55s
#d 10.128.102.0/24 10.128.102.1 1 U------um--f- v102 532d:3h:42m:55s
#d 10.128.103.0/24 10.128.103.1 1 U------um--f- v103 532d:3h:42m:55s
#d 10.128.104.0/24 10.128.104.1 1 U------um--f- v104 532d:3h:42m:55s
#d 10.128.105.0/24 10.128.105.1 1 U------um--f- v105 532d:3h:42m:56s
#d 10.128.106.0/24 10.128.106.1 1 U------um--f- v106 532d:3h:42m:55s
#d 10.128.107.0/24 10.128.107.1 1 U------um--f- v107 532d:3h:42m:55s
#d 10.128.108.0/24 10.128.108.1 1 U------um--f- v108 532d:3h:42m:55s
#d 10.128.109.0/24 10.128.109.1 1 U------um--f- v109 532d:3h:42m:55s
#d 10.128.110.0/24 10.128.110.1 1 U------um--f- v110 532d:3h:42m:55s
#d 10.128.111.0/24 10.128.111.1 1 U------um--f- v111 532d:3h:42m:56s
#d 10.128.112.0/24 10.128.112.1 1 U------um--f- v112 532d:3h:42m:55s
#d 10.128.114.0/23 10.128.114.1 1 U------um--f- v114 532d:3h:42m:55s
#d 10.128.116.0/24 10.128.116.1 1 U------um--f- v116 177d:3h:31m:21s
#d 10.128.118.0/24 10.128.118.1 1 U------um--f- v118 532d:3h:42m:55s
#d 10.128.120.0/24 10.128.120.1 1 U------um--f- v120 532d:3h:42m:55s
#d 10.128.140.0/24 10.128.140.1 1 U------um--f- v140 532d:3h:42m:55s
d 10.128.200.0/24 10.128.200.1 1 -------um---- v200 532d:3h:42m:55s
#d 10.128.211.0/24 10.128.211.1 1 U------um--f- v211 532d:3h:42m:55s

Beth_Dierks
New Contributor
Here is the Show Vlan:

VLAN Interface with name v116 created by user
Admin State: Enabled Tagging: 802.1Q Tag 116
Description: None
Virtual router: VR-Default
IPv4 Forwarding: Enabled
IPv4 MC Forwarding: Disabled
Primary IP: 10.128.116.1/24
IPv6 Forwarding: Disabled
IPv6 MC Forwarding: Disabled
IPv6: None
STPD: None
Protocol: Match all unfiltered protocols
Loopback: Disabled
NetLogin: Disabled
OpenFlow: Disabled
TRILL: Disabled
QosProfile: None configured
Egress Rate Limit Designated Port: None configured
Flood Rate Limit QosProfile: None configured
Ports: 14. (Number of active ports=8)
Untag: 3:19
Tag: 1:4, *1:29, *1:31, 2:21, *2:29, *2:31, *2:32,
3:6, *3:29, 4:23, 4:30, *4:31, *4:32
Flags: (*) Active, (!) Disabled, (g) Load Sharing port

Patrick_Voss
Extreme Employee
Can you send me a "show vlan" and "show iproute" output?
GTM-P2G8KFN