Summit x450a after reset to factory default does not keep configuration
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-22-2014 07:31 AM
Hi,
I have 2 summit x450a that after they were reset to factory default the switches started up with blank configuration as can be seen from the attached sample below and except for vlan that I was able to configure every other configuration, although seem to be accepted does not show in the console when executing "show configuration" the sections keep showing empty / blank as the attached sample
Does the switch have any "en" mode as cisco?
How Can I configure the switch?
Thanks
#
# Module bfd configuration.
#
#
# Module cfgmgr configuration.
#
#
# Module dosprotect configuration.
#
#
# Module dot1ag configuration.
#
#
# Module eaps configuration.
#
#
# Module edp configuration.
#
8 REPLIES 8
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-22-2014 10:21 AM
I would recommend upgrading to 15.3.1.4 latest patch and then reconfigure the switch. 12.4 is end of engineering .
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-22-2014 09:09 AM
Thank you in any case Robert 
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-22-2014 09:08 AM
 I have opened a case
it will not show even the simplest things
here is an example:
* X450a-24t.1 #
* X450a-24t.1 #
* X450a-24t.1 #
* X450a-24t.1 # sh configuration
#
# Module devmgr configuration.
#
#
# Module vlan configuration.
#
#
# Module fdb configuration.
#
#
# Module rtmgr configuration.
#
#
# Module mcmgr configuration.
#
#
# Module aaa configuration.
#
* X450a-24t.2 # configure snmp sysName "X450a-24t"
* X450a-24t.3 #
* X450a-24t.3 #
* X450a-24t.3 # sh configuration
#
# Module devmgr configuration.
#
#
# Module vlan configuration.
#
#
# Module fdb configuration.
#
#
# Module rtmgr configuration.
#
#
# Module mcmgr configuration.
#
#
# Module aaa configuration.
#
Press to continue or
it will not show even the simplest things
here is an example:
* X450a-24t.1 #
* X450a-24t.1 #
* X450a-24t.1 #
* X450a-24t.1 # sh configuration
#
# Module devmgr configuration.
#
#
# Module vlan configuration.
#
#
# Module fdb configuration.
#
#
# Module rtmgr configuration.
#
#
# Module mcmgr configuration.
#
#
# Module aaa configuration.
#
* X450a-24t.2 # configure snmp sysName "X450a-24t"
* X450a-24t.3 #
* X450a-24t.3 #
* X450a-24t.3 # sh configuration
#
# Module devmgr configuration.
#
#
# Module vlan configuration.
#
#
# Module fdb configuration.
#
#
# Module rtmgr configuration.
#
#
# Module mcmgr configuration.
#
#
# Module aaa configuration.
#
Press
to quit:
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-22-2014 08:52 AM
Thanks, but I am out for that release. Let us hope that someone with knowledge of 12.x notices this thread.
(Personally, I would say that the configuration was saved correctly [last line of the output]. Maybe just open a case with GTAC?)
(Personally, I would say that the configuration was saved correctly [last line of the output]. Maybe just open a case with GTAC?)
