cancel
Showing results for 
Search instead for 
Did you mean: 

X590 stack upgrade issue

X590 stack upgrade issue

Alexandr_P
Valued Contributor
Hello, colleagues!

X590 stack was with 22.6.1.4.
Issues began when tryed to upgrade stack directly to 30.7.2.1
"Installing to Slot-2(Backup): .....Error: Failed to install image on Slot-2 - tar: corrupted data"

Normally upgraded to 30.2.2.17, but again issues.
Tryed upgrade to "clean" EXOS 30.7 based on this article - Solution: Upgrade attempt fails on EXOS Summit X440-G2 stack | Extreme Portal
Force remove preview
Solution: Upgrade attempt fails on EXOS Summit X440-G2 stack | Extreme Portal
View this on Force >

but no success.
Tryed to upgrade to 30.3.1.6 but still issues:

Slot-1 X590.4 # install image onie-30.3.1.6.xos
This image will be used only after rebooting the switch!
Installing to primary partition!
Installing to Slot-2(Backup): .....Error: Failed to install image on Slot-2 - tar: corrupted data
Install image failed: (see above error message)

And below messages in logs:
1/23/2021 12:40:04.02 <Noti:EPM.install_status> User XXX: Image installation finished with status failure -tar: can't open '/scratch/onie-30.3.1.6.xos': No such file or directory
11/23/2021 12:40:03.99 <Erro:EPM.Upgrade.Fail> Upgrade failed, script: get new installer failed
11/23/2021 12:40:03.97 <Noti:EPM.Upgrade.Strt> User bigroma: Image upgrade has started.
11/23/2021 12:39:48.22 <Erro:EPM.Upgrade.Fail> Upgrade failed, script: get new installer failed
11/23/2021 12:39:42.64 <Warn:EPM.Upgrade.State> Upgrade status Sent install request to EPM peer(s).
11/23/2021 12:39:42.31 <Warn:EPM.Upgrade.State> Upgrade status Send change partition request to EPM peer(s)
11/23/2021 12:36:31.47 <Info:AAA.LogSsh> Msg from Backup : ERROR: Failed to get file "onie-30.3.1.6.xos" from primary.
11/23/2021 12:36:31.47 <Info:AAA.LogSsh> Msg from Backup : Failed to get file onie-30.3.1.6.xos on backup.
11/23/2021 12:36:30.93 <Erro:tftpd.err> received error packet: 768: write error
11/23/2021 12:35:30.97 <Info:AAA.LogSsh> Msg from Master : Did not send file "onie-30.3.1.6.xos" info to any standby's
11/23/2021 12:35:30.97 <Info:AAA.LogSsh> Msg from Master : Sent file "onie-30.3.1.6.xos" info to backup

Now we have this situation:
->show version images
Card Partition Installation Date Version Name Branch
------------------------------------------------------------------------------
Slot-1 primary Tue Nov 23 12:46:17 EET 2021 30.3.1.6 onie-30.3.1.6.xos builds/xos_30.3/30.3.1.6
Slot-1 secondary Mon Nov 22 21:59:57 EET 2021 30.2.2.17 onie-30.2.2.17.xos 30.2.2.17

Slot-2 primary Tue Nov 23 12:32:35 EET 2021 30.2.2.17 onie-30.2.2.17.xos 30.2.2.17
Slot-2 secondary Mon Nov 22 21:59:07 EET 2021 30.2.2.17 onie-30.2.2.17.xos 30.2.2.17

->show switch
...
Slot: Slot-1 * Slot-2
------------------------ ------------------------
Current State: MASTER BACKUP (In Sync)

Image Selected: secondary secondary
Image Booted: secondary secondary
Primary ver: 30.3.1.6 30.2.2.17
Secondary ver: 30.2.2.17 30.2.2.17


How could we upgrade stack without rebuild it? (disassemble, upgrade, assemble)
Maybe somebody faced with such issues?

Thank you!
2 REPLIES 2

Alexandr_P
Valued Contributor
Hello, James!

1. Stack already upgraded to 30.x but issue still persist
2. Slot 1 normally upgrading. Issue with Slot 2 upgrade

Thank you!

James_A
Valued Contributor
https://extremeportal.force.com/ExtrArticleDetail?an=000058389

  • TFTP block size was incorrectly set in some non GA EXOS versions, as well as 22.x versions prior to EXOS 22.5.1.7-patch1-7 / 22.6.1.4-patch1-8.
  • If using 22.x, upgrade to EXOS 22.5.1.7-patch1-7 / 22.6.1.4-patch1-8 before attempting 30.x install.
    GTM-P2G8KFN