X8 XFP2-QSFP28 issue
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-25-2019 02:10 PM
Hello, all!
BD-X8
card with 100G ports - BDXB-100G4X.
Inserted CFP2-QSFP28 adapters. Install transceivers - no signal.
In logs:
09/25/2019 16:55:55.32 Slot-5: aspendiags: aspenPollCfpPorts: Unsupported speed=16, media=90
09/25/2019 16:55:55.29 Slot-5: aspendiags: aspenPollCfpPorts: Unsupported speed=16, media=90
Any ideas?
Thank you!
BD-X8
card with 100G ports - BDXB-100G4X.
Inserted CFP2-QSFP28 adapters. Install transceivers - no signal.
In logs:
09/25/2019 16:55:55.32 Slot-5: aspendiags: aspenPollCfpPorts: Unsupported speed=16, media=90
09/25/2019 16:55:55.29 Slot-5: aspendiags: aspenPollCfpPorts: Unsupported speed=16, media=90
Any ideas?
Thank you!
1 REPLY 1
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-26-2019 10:51 AM
May be output can help?
# debug hal show optic-info slot 5 port 1 Optic Info for Slot 5, Port 1
[CFP#0] - 0019
MOD_PRESENT = 1
GLB_ALRM = 0
RX_LOS = 0
PRG_ALRM1 = 1 (HIPWR_ON)
PRG_ALRM2 = 1 (MOD_READY)
PRG_ALRM3 = 0 (MOD_FAULT)
-- CFP NVR1 --
id: CFP2 (11)
Power Class: 3.0W max (0)
Connector: Unknown-(0)
10/40G comp code: (0)
Number of Network Lanes: 4
Number of Host Lanes: 10
Media Properties: SMF (0)
Network Lane Bit Rate: 0.00 Gbps
Host Lane Bit Rate: 0.00 Gbps
Max SMF length: 0 km
Max MMF length: 0 km
Max Copper length: 0 km
vendor: BROCADE
oui: 0 5 1E
partNumber: 84-1002844-01
CFP MSA Hw Spec: 1.0
CFP MSA Mgmt Spec: 2.2
hw rev: 10.0
fw rev: 0.0
wavelength: (0x0000)
maxTemp: 0/0 deg C
serialNumber: DZE3338L0G7
manufactureDate: 09/24/15
ddmiMonType: 0
Rx Pwr Measure type: OMA
Tx Pwr Measure type: OMA
ddmiCapModule: 0
ddmiCapPerLane: 0
enhancedOptions: 0
enhancedOptions2: 0
-- CFP Vendor NVR1 --
Version: ffff
Extreme Part Number: ЪЪЪЪЪЪЪЪ
Extreme Serial Number: ЪЪЪЪЪЪЪЪ
Digest: ffffffffffffffffffffffffffffffffffffffff
-- CFP Module VR1 --
Module State: Initialize (0)
Electrical Interface: Unspecified (0)
Enabled Current Latched
------------------------
Global Alarm Summary 0x0000
# debug hal show optic-info slot 5 port 1 Optic Info for Slot 5, Port 1
[CFP#0] - 0019
MOD_PRESENT = 1
GLB_ALRM = 0
RX_LOS = 0
PRG_ALRM1 = 1 (HIPWR_ON)
PRG_ALRM2 = 1 (MOD_READY)
PRG_ALRM3 = 0 (MOD_FAULT)
-- CFP NVR1 --
id: CFP2 (11)
Power Class: 3.0W max (0)
Connector: Unknown-(0)
10/40G comp code: (0)
Number of Network Lanes: 4
Number of Host Lanes: 10
Media Properties: SMF (0)
Network Lane Bit Rate: 0.00 Gbps
Host Lane Bit Rate: 0.00 Gbps
Max SMF length: 0 km
Max MMF length: 0 km
Max Copper length: 0 km
vendor: BROCADE
oui: 0 5 1E
partNumber: 84-1002844-01
CFP MSA Hw Spec: 1.0
CFP MSA Mgmt Spec: 2.2
hw rev: 10.0
fw rev: 0.0
wavelength: (0x0000)
maxTemp: 0/0 deg C
serialNumber: DZE3338L0G7
manufactureDate: 09/24/15
ddmiMonType: 0
Rx Pwr Measure type: OMA
Tx Pwr Measure type: OMA
ddmiCapModule: 0
ddmiCapPerLane: 0
enhancedOptions: 0
enhancedOptions2: 0
-- CFP Vendor NVR1 --
Version: ffff
Extreme Part Number: ЪЪЪЪЪЪЪЪ
Extreme Serial Number: ЪЪЪЪЪЪЪЪ
Digest: ffffffffffffffffffffffffffffffffffffffff
-- CFP Module VR1 --
Module State: Initialize (0)
Electrical Interface: Unspecified (0)
Enabled Current Latched
------------------------
Global Alarm Summary 0x0000
