Adding on X670G2 to an existing OSPF network
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-13-2016 07:23 AM
The OSPF network is a X460-24t and two cisco routers. all configured in the same area.
The fimrware of the X460 and the X670 is 16.1.2.14.
But for some reason the X670 is not learning or distribute any route.
How can I troubleshoot this ?
The fimrware of the X460 and the X670 is 16.1.2.14.
But for some reason the X670 is not learning or distribute any route.
How can I troubleshoot this ?
Johan Hendrik
System Architect
Audax
27 REPLIES 27
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-14-2016 03:00 AM
Output switch X670
CS-A01-2.1 # sh ospf int
CS-A01-2.1 # sh ospf interfaces
VLAN IP Address AREA ID Flags Cost State Neighbors
GIDAT 144.2.144.249 /21 0.0.0.0 -rif--- 2/A ODR 4
GIDTP 10.2.120.254 /24 0.0.0.0 -rif--- 4/A DR 0
GITEST 10.2.128.254 /24 0.0.0.0 -rif--- 2/A DR 0
GIVOIP1 10.2.161.254 /24 0.0.0.0 -rif--- 4/A DR 0
Flags: b - BFD protection configured, D - Duplicate address detected on VLAN,
f - Interface Forwarding Enabled, i - Interface OSPF Enabled,
n - Multinetted VLAN, p - Passive Interface, r - Router OSPF Enable,
T - Tentative address.
Cost: A - Automatic Cost, C - Configured Cost.
Total number of interfaces: 13
CS-A01-2.2 # sh ospf interfaces detail
Interface(rif1000020): 144.2.144.249/21 Vlan: GIDAT OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.254 Link Type: broadcast(auto) Passive: No
Cost: 2/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: ODR Number of events: 1
DR RtId: 10.216.167.31 DR IP addr: 144.2.144.250 BDR IP addr: 144.2.144.250
Num Neighbor State Change to FULL : 1
BFD Protection: Off
Neighbors:
RtrId: 144.2.144.254 IpAddr: 144.2.144.254 Pri: 1 Type: Auto
State: 2WAY Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:00
Options (0x0): Opaque LSA: No
BFD Session State: None
RtrId: 192.168.178.63 IpAddr: 144.2.144.251 Pri: 10 Type: Auto
State: INIT Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:08
Options (0x0): Opaque LSA: No
BFD Session State: None
RtrId: 10.2.144.253 IpAddr: 144.2.144.253 Pri: 1 Type: Auto
State: 2WAY Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:09
Options (0x0): Opaque LSA: No
BFD Session State: None
RtrId: 10.216.167.31 IpAddr: 144.2.144.250 Pri: 10 Type: Auto
State: FULL Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:05
Options (0x52): Opaque LSA: Yes
BFD Session State: None
Interface(rif1000023): 10.2.120.254/24 Vlan: GIDTP OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.254 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: DR Number of events: 1
DR RtId: 10.2.144.254 DR IP addr: 10.2.120.254 BDR IP addr: 0.0.0.0
Press to continue or
CS-A01-2.1 # sh ospf int
CS-A01-2.1 # sh ospf interfaces
VLAN IP Address AREA ID Flags Cost State Neighbors
GIDAT 144.2.144.249 /21 0.0.0.0 -rif--- 2/A ODR 4
GIDTP 10.2.120.254 /24 0.0.0.0 -rif--- 4/A DR 0
GITEST 10.2.128.254 /24 0.0.0.0 -rif--- 2/A DR 0
GIVOIP1 10.2.161.254 /24 0.0.0.0 -rif--- 4/A DR 0
Flags: b - BFD protection configured, D - Duplicate address detected on VLAN,
f - Interface Forwarding Enabled, i - Interface OSPF Enabled,
n - Multinetted VLAN, p - Passive Interface, r - Router OSPF Enable,
T - Tentative address.
Cost: A - Automatic Cost, C - Configured Cost.
Total number of interfaces: 13
CS-A01-2.2 # sh ospf interfaces detail
Interface(rif1000020): 144.2.144.249/21 Vlan: GIDAT OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.254 Link Type: broadcast(auto) Passive: No
Cost: 2/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: ODR Number of events: 1
DR RtId: 10.216.167.31 DR IP addr: 144.2.144.250 BDR IP addr: 144.2.144.250
Num Neighbor State Change to FULL : 1
BFD Protection: Off
Neighbors:
RtrId: 144.2.144.254 IpAddr: 144.2.144.254 Pri: 1 Type: Auto
State: 2WAY Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:00
Options (0x0): Opaque LSA: No
BFD Session State: None
RtrId: 192.168.178.63 IpAddr: 144.2.144.251 Pri: 10 Type: Auto
State: INIT Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:08
Options (0x0): Opaque LSA: No
BFD Session State: None
RtrId: 10.2.144.253 IpAddr: 144.2.144.253 Pri: 1 Type: Auto
State: 2WAY Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:09
Options (0x0): Opaque LSA: No
BFD Session State: None
RtrId: 10.216.167.31 IpAddr: 144.2.144.250 Pri: 10 Type: Auto
State: FULL Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:05
Options (0x52): Opaque LSA: Yes
BFD Session State: None
Interface(rif1000023): 10.2.120.254/24 Vlan: GIDTP OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.254 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: DR Number of events: 1
DR RtId: 10.2.144.254 DR IP addr: 10.2.120.254 BDR IP addr: 0.0.0.0
Press
to quit:Num Neighbor State Change to FULL : 0
BFD Protection: Off
Neighbors:
Interface(rif1000040): 10.2.128.254/24 Vlan: GITEST OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.254 Link Type: broadcast(auto) Passive: No
Cost: 2/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: DR Number of events: 1
DR RtId: 10.2.144.254 DR IP addr: 10.2.128.254 BDR IP addr: 0.0.0.0
Num Neighbor State Change to FULL : 0
BFD Protection: Off
Neighbors:
Interface(rif1000043): 10.2.161.254/24 Vlan: GIVOIP1 OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.254 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: DR Number of events: 1
DR RtId: 10.2.144.254 DR IP addr: 10.2.161.254 BDR IP addr: 0.0.0.0
Num Neighbor State Change to FULL : 0
BFD Protection: Off
Neighbors:
CS-A01-2.3 # sh ospf ne
CS-A01-2.3 # sh ospf neighbor
Neighbor ID Pri State Up/Dead Time Address Interface
BFD Session State
==========================================================================================
144.2.144.254 1 2WAY /DROTHER 00:20:47:25/00:00:00:02 144.2.144.254 GIDAT
None
192.168.178.63 10 INIT /DR 00:20:47:29/00:00:00:01 144.2.144.251 GIDAT
None
10.2.144.253 1 2WAY /DROTHER 00:20:47:32/00:00:00:10 144.2.144.253 GIDAT
None
10.216.167.31 10 FULL /BDR 00:20:47:34/00:00:00:07 144.2.144.250 GIDAT
None
Total number of neighbors: 4 (1 neighbor in Full state)
CS-A01-2.4 # sh conf ospf
#
# Module ospf configuration.
#
configure ospf routerid 10.2.144.254
enable ospf
enable ospf export direct cost 2 type ase-type-1
enable ospf export static cost 2 type ase-type-1
configure ospf add vlan GIDAT area 0.0.0.0
configure ospf add vlan GIDTP area 0.0.0.0
configure ospf add vlan GITEST area 0.0.0.0
configure ospf add vlan GIVOIP1 area 0.0.0.0
CS-A01-2.5 #
Johan Hendrik
System Architect
Audax
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-14-2016 03:00 AM
Output switch X460:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.12.14 10:35:02 =~=~=~=~=~=~=~=~=~=~=~=
telnet session telnet0 on /dev/ptyb0
Connected to Core Switch at Audax Gilze CS-F01-1
Closed system, authorised users only !!
Session will be logged.
login: admin
password:
ExtremeXOS
Copyright (C) 1996-2015 Extreme Networks. All rights reserved.
This product is protected by one or more US patents listed at http://www.extremenetworks.com/patents along with their foreign counterparts.
==============================================================================
Press the or '?' key at any time for completions.
Remember to save your configuration changes.
CS-F01-1.1 # sh ospf in
CS-F01-1.1 # sh ospf interfaces
VLAN IP Address AREA ID Flags Cost State Neighbors
GI-AP 10.2.114.253 /24 0.0.0.0 -rif--- 4/A DR 0
GI-MGMT 10.2.112.253 /24 0.0.0.0 -rif--- 4/A DR 0
GIBEHEER 144.2.112.253 /24 0.0.0.0 -rif--- 4/A DR 0
GIDAT 144.2.144.253 /21 0.0.0.0 -rif--- 4/A ODR 4
gidat1 10.2.144.253 /21 0.0.0.0 -rif--- 4/A DR 0
GINFS 144.2.166.253 /24 0.0.0.0 -rif--- 4/A BDR 1
GIVIDEO 10.2.38.253 /24 0.0.0.0 -rif--- 4/A DR 0
Flags: b - BFD protection configured, D - Duplicate address detected on VLAN,
f - Interface Forwarding Enabled, i - Interface OSPF Enabled,
n - Multinetted VLAN, p - Passive Interface, r - Router OSPF Enable,
T - Tentative address.
Cost: A - Automatic Cost, C - Configured Cost.
Total number of interfaces: 17
CS-F01-1.2 #
CS-F01-1.2 # sh ospf interfaces det
Interface(rif1000009): 10.2.114.253/24 Vlan: GI-AP OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.253 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: DR Number of events: 1
DR RtId: 10.2.144.253 DR IP addr: 10.2.114.253 BDR IP addr: 0.0.0.0
Num Neighbor State Change to FULL : 1
BFD Protection: Off
Press to continue or
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.12.14 10:35:02 =~=~=~=~=~=~=~=~=~=~=~=
telnet session telnet0 on /dev/ptyb0
Connected to Core Switch at Audax Gilze CS-F01-1
Closed system, authorised users only !!
Session will be logged.
login: admin
password:
ExtremeXOS
Copyright (C) 1996-2015 Extreme Networks. All rights reserved.
This product is protected by one or more US patents listed at http://www.extremenetworks.com/patents along with their foreign counterparts.
==============================================================================
Press the
Remember to save your configuration changes.
CS-F01-1.1 # sh ospf in
CS-F01-1.1 # sh ospf interfaces
VLAN IP Address AREA ID Flags Cost State Neighbors
GI-AP 10.2.114.253 /24 0.0.0.0 -rif--- 4/A DR 0
GI-MGMT 10.2.112.253 /24 0.0.0.0 -rif--- 4/A DR 0
GIBEHEER 144.2.112.253 /24 0.0.0.0 -rif--- 4/A DR 0
GIDAT 144.2.144.253 /21 0.0.0.0 -rif--- 4/A ODR 4
gidat1 10.2.144.253 /21 0.0.0.0 -rif--- 4/A DR 0
GINFS 144.2.166.253 /24 0.0.0.0 -rif--- 4/A BDR 1
GIVIDEO 10.2.38.253 /24 0.0.0.0 -rif--- 4/A DR 0
Flags: b - BFD protection configured, D - Duplicate address detected on VLAN,
f - Interface Forwarding Enabled, i - Interface OSPF Enabled,
n - Multinetted VLAN, p - Passive Interface, r - Router OSPF Enable,
T - Tentative address.
Cost: A - Automatic Cost, C - Configured Cost.
Total number of interfaces: 17
CS-F01-1.2 #
CS-F01-1.2 # sh ospf interfaces det
Interface(rif1000009): 10.2.114.253/24 Vlan: GI-AP OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.253 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: DR Number of events: 1
DR RtId: 10.2.144.253 DR IP addr: 10.2.114.253 BDR IP addr: 0.0.0.0
Num Neighbor State Change to FULL : 1
BFD Protection: Off
Press
to quit:
Neighbors:
Interface(rif1000006): 10.2.112.253/24 Vlan: GI-MGMT OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.253 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: DR Number of events: 1
DR RtId: 10.2.144.253 DR IP addr: 10.2.112.253 BDR IP addr: 0.0.0.0
Num Neighbor State Change to FULL : 0
BFD Protection: Off
Neighbors:
Interface(rif1000011): 144.2.112.253/24 Vlan: GIBEHEER OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.253 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
Pressto continue or to quit:State: DR Number of events: 1
DR RtId: 10.2.144.253 DR IP addr: 144.2.112.253 BDR IP addr: 0.0.0.0
Num Neighbor State Change to FULL : 0
BFD Protection: Off
Neighbors:
Interface(rif1000012): 144.2.144.253/21 Vlan: GIDAT OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.253 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: ODR Number of events: 1
DR RtId: 192.168.178.63 DR IP addr: 144.2.144.251 BDR IP addr: 144.2.144.250
Num Neighbor State Change to FULL : 1381
BFD Protection: Off
Neighbors:
RtrId: 192.168.178.63 IpAddr: 144.2.144.251 Pri: 10 Type: Auto
State: FULL Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:01
Options (0x52): Opaque LSA: Yes
BFD Session State: None
Pressto continue or to quit:
RtrId: 10.2.144.254 IpAddr: 144.2.144.249 Pri: 1 Type: Auto
State: 2WAY Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:05
Options (0x0): Opaque LSA: No
BFD Session State: None
RtrId: 144.2.144.254 IpAddr: 144.2.144.254 Pri: 1 Type: Auto
State: 2WAY Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:02
Options (0x42): Opaque LSA: Yes
BFD Session State: None
RtrId: 10.216.167.31 IpAddr: 144.2.144.250 Pri: 10 Type: Auto
State: FULL Dr: 144.2.144.251 BDR: 144.2.144.250 Dead Time: 00:00:00:09
Options (0x52): Opaque LSA: Yes
BFD Session State: None
Interface(rif1000013): 10.2.144.253/21 Vlan: gidat1 OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.253 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
Pressto continue or to quit:State: DR Number of events: 1
DR RtId: 10.2.144.253 DR IP addr: 10.2.144.253 BDR IP addr: 0.0.0.0
Num Neighbor State Change to FULL : 1
BFD Protection: Off
Neighbors:
Interface(rif1000023): 144.2.166.253/24 Vlan: GINFS OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.253 Link Type: broadcast(auto) Passive: No
Pressto continue or to quit:Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: BDR Number of events: 1
DR RtId: 144.2.144.254 DR IP addr: 144.2.166.254 BDR IP addr: 144.2.166.253
Num Neighbor State Change to FULL : 119
BFD Protection: Off
Neighbors:
RtrId: 144.2.144.254 IpAddr: 144.2.166.254 Pri: 1 Type: Auto
State: FULL Dr: 144.2.166.254 BDR: 144.2.166.253 Dead Time: 00:00:00:06
Options (0x42): Opaque LSA: Yes
BFD Session State: None
Interface(rif1000034): 10.2.38.253/24 Vlan: GIVIDEO OSPF: ENABLED Router: ENABLED
AreaId: 0.0.0.0 RtId: 10.2.144.253 Link Type: broadcast(auto) Passive: No
Cost: 4/A Priority: 1 Transit Delay: 1 DAD State:Valid
Hello Interval: 10s Rtr Dead Time: 40s Retransmit Interval: 5s
Wait Timer: 40s(auto)
Authentication: NONE
State: DR Number of events: 1
DR RtId: 10.2.144.253 DR IP addr: 10.2.38.253 BDR IP addr: 0.0.0.0
Num Neighbor State Change to FULL : 1
BFD Protection: Off
Neighbors:
Pressto continue or to quit:CS-F01-1.3 #
CS-F01-1.3 # sh ospf interfaces detneig
CS-F01-1.3 # sh ospf neighbor
Neighbor ID Pri State Up/Dead Time Address Interface
BFD Session State
==========================================================================================
192.168.178.63 10 FULL /DR 02:05:22:36/00:00:00:07 144.2.144.251 GIDAT
None
10.2.144.254 1 2WAY /DROTHER 05:02:20:52/00:00:00:01 144.2.144.249 GIDAT
None
144.2.144.254 1 2WAY /DROTHER 14:00:34:25/00:00:00:08 144.2.144.254 GIDAT
None
10.216.167.31 10 FULL /BDR 14:00:34:25/00:00:00:07 144.2.144.250 GIDAT
None
144.2.144.254 1 FULL /DR 00:02:34:09/00:00:00:01 144.2.166.254 GINFS
None
Total number of neighbors: 5 (3 neighbors in Full state)
CS-F01-1.4 # sh conf ospf
#
# Module ospf configuration.
#
configure ospf routerid 10.2.144.253
enable ospf
enable ospf export direct cost 2 type ase-type-1
enable ospf export static cost 2 type ase-type-1
configure ospf add vlan GI-AP area 0.0.0.0
configure ospf add vlan GI-MGMT area 0.0.0.0
configure ospf add vlan GIBEHEER area 0.0.0.0
configure ospf add vlan GIDAT area 0.0.0.0
configure ospf add vlan gidat1 area 0.0.0.0
configure ospf add vlan GINFS area 0.0.0.0
configure ospf add vlan GIVIDEO area 0.0.0.0
CS-F01-1.5 # exit
Johan Hendrik
System Architect
Audax
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-14-2016 03:00 AM
how would you like the output ?
Johan Hendrik
System Architect
Audax
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-13-2016 02:35 PM
See OSPF neighbor adjacency is "Full" but not adding routes into route table regarding the above suggestion.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎12-13-2016 01:43 PM
Hi Johan,
if OSPF adjacencies are formed, but no routes seen using the link, the problem might be a point-to-point interface configuration on only one of the routers. Since you did not specify point-to-point in the OSPF config you showed us, I would suggest you check if the Cisco is using a point-to-point interface to the Extreme X670G2.
Erik
if OSPF adjacencies are formed, but no routes seen using the link, the problem might be a point-to-point interface configuration on only one of the routers. Since you did not specify point-to-point in the OSPF config you showed us, I would suggest you check if the Cisco is using a point-to-point interface to the Extreme X670G2.
Erik
