New GTAC Knowledge Articles July 20-25, 2015
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎07-28-2015 05:04 PM
Here are the new articles that were published last week (July 20 - July 25, 2015) in GTAC Knowledge:
Monday July 20, 2015:
none
Tuesday July 21, 2015:
K-Series fabric module will not fully boot with debug log message: failed to initialize PHY hardware...
S4 / S8 OPTION MODULE COMPATIBILITY QUESTIONS
: Switch: mainboard temperature (0 C) is reaching minimum limit (-10 Celsius)
Captive portal not working after upgrading software
S-Series Blade keeps going off line
Clients experience timeouts when there is a change in connection
Wednesday July 22, 2015
Receiving SNMPv1/v2 Logs When Protocols Are Not In Use
One or More Ports on B5G124-48P2 Securestack Do Not Receive Data
Where to Find the Transceivers Data Sheet?
Why do some Fingerprints have a lower confidence level if the pattern is exact?
What is the best practice firewall settings to be configured on WM3000 series?
How to copy backup from EWC to FTP
Thursday July 23, 2015
OF Connect install
How To Debug OSPF Adjacency?
C5-Series reports "Exceeded Maximum size allowed" error when Saving Configs
How to Add MAC Addresses to NAC End-System Groups via NAC Request Tool
Where are the File Transfer Settings configured in NetSight Inventory Manager
hardware FDB table full error logs
Friday July 24, 2015
What is the benefit of using a ring topology in a stack?
Poor Wireless Performance - Wireless Clients Disassociating Unexpectedly
Errors on S module after replacement adding option module
Poor performance with the AP3705 running 9.15.05 firmware.
How to hot swap a Dragon EMS hard drive
radDecodeVsa: Unknown vendor 311
Saturday July 25, 2015
Switch throws Power usage data unknown for PSU Part log after the reboot
Error messages when swapping 10G4Xa for 8900- 10G8X-xl modules
The snmpMaster process crashes repeatedly with signal 11 while using Netsight
Modular blade reset with error: Fuji PRS MAIN Intr:
Monday July 20, 2015:
none
Tuesday July 21, 2015:
K-Series fabric module will not fully boot with debug log message: failed to initialize PHY hardware...
S4 / S8 OPTION MODULE COMPATIBILITY QUESTIONS
: Switch: mainboard temperature (0 C) is reaching minimum limit (-10 Celsius)
Captive portal not working after upgrading software
S-Series Blade keeps going off line
Clients experience timeouts when there is a change in connection
Wednesday July 22, 2015
Receiving SNMPv1/v2 Logs When Protocols Are Not In Use
One or More Ports on B5G124-48P2 Securestack Do Not Receive Data
Where to Find the Transceivers Data Sheet?
Why do some Fingerprints have a lower confidence level if the pattern is exact?
What is the best practice firewall settings to be configured on WM3000 series?
How to copy backup from EWC to FTP
Thursday July 23, 2015
OF Connect install
How To Debug OSPF Adjacency?
C5-Series reports "Exceeded Maximum size allowed" error when Saving Configs
How to Add MAC Addresses to NAC End-System Groups via NAC Request Tool
Where are the File Transfer Settings configured in NetSight Inventory Manager
hardware FDB table full error logs
Friday July 24, 2015
What is the benefit of using a ring topology in a stack?
Poor Wireless Performance - Wireless Clients Disassociating Unexpectedly
Errors on S module after replacement adding option module
Poor performance with the AP3705 running 9.15.05 firmware.
How to hot swap a Dragon EMS hard drive
radDecodeVsa: Unknown vendor 311
Saturday July 25, 2015
Switch throws Power usage data unknown for PSU Part log after the reboot
Error messages when swapping 10G4Xa for 8900- 10G8X-xl modules
The snmpMaster process crashes repeatedly with signal 11 while using Netsight
Modular blade reset with error: Fuji PRS MAIN Intr:
2 REPLIES 2
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎07-29-2015 05:02 PM
We are not tracking any issues with the 3705 and 9.21 code.
-Doug
-Doug
Doug Hyde
Director, Technical Support / Extreme Networks
Director, Technical Support / Extreme Networks
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎07-29-2015 01:09 PM
Poor performance with the AP3705 running 9.15.05 firmware.
In regards to this article, is that a general issue and also affects v9.21?
I plan to upgrade a 400+AP3705 network and pretty soon.
Thanks,
Ron
In regards to this article, is that a general issue and also affects v9.21?
I plan to upgrade a 400+AP3705 network and pretty soon.
Thanks,
Ron