I need to set up a network as shown in the diagram. Core is the Voss system, Access is the Exos system, and my core layer uses SPBM and VRRP technology for redundancy. The core and access are interconnected through SMLT technology. In my actual application, I found that when I disconnect an uplink, my access network is disconnected and cannot be restored until 20 packets are discarded and restored to normal. What is the reason for this?
Here is my core configuration script：
interface loopback 1
ip address 1.1.1.1/32
exit
spbm
spbm ethertype 0x8100
prompt HSBC-SZ-JF-Core_SW-001
router isis
spbm 1
spbm 1 b-vid 4051,4052 primary 4051
system-id 00bb.0021.0001
spbm 1 nick-name 1.21.01
manual-area 49.0000
spbm 1 multicast enable
spbm 1 smlt-peer-system-id 00bb.0021.0002
spbm 1 smlt-virtual-bmac 00:bb:00:21:00:0f
ip-source-address 1.1.1.1
spbm 1 ip enable
exit
vlan create 4051 type spbm-bvlan
vlan create 4052 type spbm-bvlan
vlan members remove 1 1/1-1/18
mlt 17 enable name vIST
mlt 17 member 1/17-1/18
mlt 17 encapsulation dot1q
interface mlt 17
isis
isis spbm 1
isis enable
exit
vlan create 4053 type port-mstprstp 0
vlan i-sid 4053 1004053
interface vlan 4053
ip address 10.10.0.1/30
exit
virtual-ist peer-ip 10.10.0.2 vlan 4053
cfm spbm mepid 1
cfm spbm enable
lacp smlt-sys-id 00:bb:00:21:00:ff
router isis enable
interface gig 1/17-1/18
no shutdown
vlan create 11 name WuYe_YX type port-mstprstp 0
vlan create 12 name HYS_YX type port-mstprstp 0
vlan create 13 name ****ang_YX type port-mstprstp 0
vlan i-sid 11 1000011
vlan i-sid 12 1000012
vlan i-sid 13 1000013
int vlan 11
ip address 10.0.11.253/24
ip dhcp-relay
ip vrrp version 2
ip vrrp address 11 10.0.11.254
ip vrrp 11 backup-master enable
ip vrrp 11 priority 200
ip vrrp 11 enable
ip spb-multicast enable
exit
int vlan 12
ip address 10.0.12.253/24
ip dhcp-relay
ip vrrp version 2
ip vrrp address 12 10.0.12.254
ip vrrp 12 backup-master enable
ip vrrp 12 priority 200
ip vrrp 12 enable
ip spb-multicast enable
exit
int vlan 13
ip address 10.0.13.253/24
ip dhcp-relay
ip vrrp version 2
ip vrrp address 13 10.0.13.254
ip vrrp 13 backup-master enable
ip vrrp 13 priority 200
ip vrrp 13 enable
ip spb-multicast enable
exit
mlt 1 enable name edge_B2
mlt 1 member 1/1
mlt 1 encapsulation dot1q
interface mlt 1
smlt
fa
fa enable
fa message-authentication
fa authentication-key HSBC
exit
mlt 2 enable name edge_B1
mlt 2 member 1/2
mlt 2 encapsulation dot1q
interface mlt 2
smlt
fa
fa enable
fa message-authentication
fa authentication-key HSBC
exit
mlt 3 enable name edge_1F
mlt 3 member 1/3
mlt 3 encapsulation dot1q
interface mlt 3
smlt
fa
fa enable
fa message-authentication
fa authentication-key HSBC
exit
The following is the configuration script I connected to：
create vlan vlan11 tag 11
create vlan vlan12 tag 12
create vlan vlan13 tag 13
configure vlan vlan11 add nsi 1000011
configure vlan vlan12 add nsi 1000012
configure vlan vlan13 add nsi 1000013
enable stpd s0 auto-bind vlan vlan11
enable stpd s0 auto-bind vlan vlan12
enable stpd s0 auto-bind vlan vlan13
enable sharing 59 grouping 59-60
configure fabric attach port 59 authentication enable
configure fabric attach ports 59 authentication key HSBC
configure fabric attach port 60 authentication enable
configure fabric attach ports 60 authentication key HSBC
configure vlan vlan11 add ports 59 tagged
configure vlan vlan12 add ports 59 tagged
configure vlan vlan13 add ports 59 tagged
configure vlan vlan11 add ports 27-44 untagged
1 ACCEPTED SOLUTION
