This website uses cookies. By clicking Accept, you consent to the use of cookies. Click Here to learn more about how we use cookies.
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Extreme Networks
- Community List
- Switching & Routing
- ExtremeSwitching (VSP/Fabric Engine)
- ONA (Open Network Adapter)
Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
ONA (Open Network Adapter)
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-31-2019 07:51 PM
Hi everyone,
I have some misunderstanding about ONA (Open Network Adapter). If I have one main Site and
several Branches, can I use one VSP switch in Central Office and one ONA adapter per Branch if I`m
going to establish secure connection over the Internet between all of my Sites (hub-and-spoke topology)? Or I have to use some additional equipment in Branch Offices?
Maybe it`s a stupid question, but I can`t find any information about this adapter, even in EN
pricelist there is nothing alike this adapter.
I have some misunderstanding about ONA (Open Network Adapter). If I have one main Site and
several Branches, can I use one VSP switch in Central Office and one ONA adapter per Branch if I`m
going to establish secure connection over the Internet between all of my Sites (hub-and-spoke topology)? Or I have to use some additional equipment in Branch Offices?
Maybe it`s a stupid question, but I can`t find any information about this adapter, even in EN
pricelist there is nothing alike this adapter.
Solved! Go to Solution.
1 ACCEPTED SOLUTION
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
02-01-2019 12:59 PM
Below is the thing:
Fabric Extend Allows you to tunnel your L2 VSNs, IP Shortcuts, and L3 VSNs over a non-SPB network. This could be a carrier network or another backbone network that is not running SPB. There is the IP tunnel method, which uses VXLAN header and that uses point-to-point tunnels. The MTU required size is 1594 or 1600 bytes. This is enforced. We do not do fragmentation on the VSP 7200 or VSP 8000. IS-IS interface won't come up if the connnection does not support this MTU size. If the carrier can not provide a large enough MTU, you will need to use the VSP 4000 with an ONA to perform packet fragmentation and reassembly.
The ONA is only used on the VSP 4000 for Fabric Extend. The VSP 4000 can support L2VSNs without ONA. The VSP 4000 doesn't have the computing power that the VSP 8000 and VSP 7200 have to support IP tunnels. The ONA allows packet fragmenting which is not supported supported on 7200 and 8000.
So Basically, VSP 7200 and 8000 support all FE capabilities except packet fragmentation. For that you need an VSP 4000 with ONA on both sides.
If the tunnels are exclusively L2 and intermediate devices support a 1600 byte MTU, you can use VSP 4000 without ONA
Hope this helps!
DILRAJ
Fabric Extend Allows you to tunnel your L2 VSNs, IP Shortcuts, and L3 VSNs over a non-SPB network. This could be a carrier network or another backbone network that is not running SPB. There is the IP tunnel method, which uses VXLAN header and that uses point-to-point tunnels. The MTU required size is 1594 or 1600 bytes. This is enforced. We do not do fragmentation on the VSP 7200 or VSP 8000. IS-IS interface won't come up if the connnection does not support this MTU size. If the carrier can not provide a large enough MTU, you will need to use the VSP 4000 with an ONA to perform packet fragmentation and reassembly.
The ONA is only used on the VSP 4000 for Fabric Extend. The VSP 4000 can support L2VSNs without ONA. The VSP 4000 doesn't have the computing power that the VSP 8000 and VSP 7200 have to support IP tunnels. The ONA allows packet fragmenting which is not supported supported on 7200 and 8000.
So Basically, VSP 7200 and 8000 support all FE capabilities except packet fragmentation. For that you need an VSP 4000 with ONA on both sides.
If the tunnels are exclusively L2 and intermediate devices support a 1600 byte MTU, you can use VSP 4000 without ONA
Hope this helps!
DILRAJ
6 REPLIES 6
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
06-18-2019 11:48 AM
DILRAJ, I just read this and have a similar customer request, and I just want to make sure this is right...I can make an FE tunnel over the Internet? (I have done it in a mesh type setup with MPLS and some 4450s and ONAs). So to test, if I take one 4450 and an ONA, put it in my house, take another, put it in my neighbors, use the correct addresses/default gateways...I should be able to bring up a tunnel, over the internet (not MPLS)? Is it secure? (I'm guessing yes) and is there a rate limit? Thanks for any help and for this thread!
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
02-04-2019 07:52 AM
Thank you, Dilraj. Now it`s all clear to me!
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
02-01-2019 12:59 PM
Below is the thing:
Fabric Extend Allows you to tunnel your L2 VSNs, IP Shortcuts, and L3 VSNs over a non-SPB network. This could be a carrier network or another backbone network that is not running SPB. There is the IP tunnel method, which uses VXLAN header and that uses point-to-point tunnels. The MTU required size is 1594 or 1600 bytes. This is enforced. We do not do fragmentation on the VSP 7200 or VSP 8000. IS-IS interface won't come up if the connnection does not support this MTU size. If the carrier can not provide a large enough MTU, you will need to use the VSP 4000 with an ONA to perform packet fragmentation and reassembly.
The ONA is only used on the VSP 4000 for Fabric Extend. The VSP 4000 can support L2VSNs without ONA. The VSP 4000 doesn't have the computing power that the VSP 8000 and VSP 7200 have to support IP tunnels. The ONA allows packet fragmenting which is not supported supported on 7200 and 8000.
So Basically, VSP 7200 and 8000 support all FE capabilities except packet fragmentation. For that you need an VSP 4000 with ONA on both sides.
If the tunnels are exclusively L2 and intermediate devices support a 1600 byte MTU, you can use VSP 4000 without ONA
Hope this helps!
DILRAJ
Fabric Extend Allows you to tunnel your L2 VSNs, IP Shortcuts, and L3 VSNs over a non-SPB network. This could be a carrier network or another backbone network that is not running SPB. There is the IP tunnel method, which uses VXLAN header and that uses point-to-point tunnels. The MTU required size is 1594 or 1600 bytes. This is enforced. We do not do fragmentation on the VSP 7200 or VSP 8000. IS-IS interface won't come up if the connnection does not support this MTU size. If the carrier can not provide a large enough MTU, you will need to use the VSP 4000 with an ONA to perform packet fragmentation and reassembly.
The ONA is only used on the VSP 4000 for Fabric Extend. The VSP 4000 can support L2VSNs without ONA. The VSP 4000 doesn't have the computing power that the VSP 8000 and VSP 7200 have to support IP tunnels. The ONA allows packet fragmenting which is not supported supported on 7200 and 8000.
So Basically, VSP 7200 and 8000 support all FE capabilities except packet fragmentation. For that you need an VSP 4000 with ONA on both sides.
If the tunnels are exclusively L2 and intermediate devices support a 1600 byte MTU, you can use VSP 4000 without ONA
Hope this helps!
DILRAJ
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
02-01-2019 12:28 PM
If you plan to use VSP 4000 then yes you need ONA.
