AP7562i count of radios issue

[Aviv_Kedem]

Hello community,

I have AP7562i is 3x3 with 3 RF connectors: R1-A,R1-B, R1-C.
When disconnecting the antenna from R1-A connector, but R1-B & R1-C still connected to their connectors - the transmit power is dropped to near 0.
It seems R1-B & R1-C RF connectors are not transmitting at all.

CLI output:

show ver
AP7562 version 5.9.2.5-001R
Copyright (c) 2004-2018 Extreme Networks, Inc. All rights reserved.
Booted from primary

ap7562-xxxxxx uptime is 0 days, 00 hours 03 minutes
CPU is ARMv7, No. of CPUs 2
Base ethernet MAC address is xxxxxxxxxxxxxx
System serial number is xxxxxxxxxxxxxx
Model number is AP-7562-670042-xx

ap7562-xxxxxx#show wi ra de

Radio: 74-67-F7-xx-xx-xx:R1, alias ap7562-xxxxxx:R1
STATE : On
PHY INFO : Bssid: 74-67-F7-xx-xx-xx RF-Mode: 2.4GHz-wlan
ACCESS POINT : Name: ap7562-xxxxxx Location: default Placement: Outdoor
CHANNEL : Current: 1 Configured: smt Width: 20MHz
TRANSMIT POWER : 20 dBm
ANTENNA USAGE : 3x3
MAXIMUM DATA RATES : Phy: 288 Mbps User: 216 Mbps
PHY SETTINGS : Short Preamble: N Dual Channel: N Spectrum Mgmt: N
RATE SELECTION : Standard
ANTENNA DOWNTILT : Not-Supported
RADIO SHARE MODE : Off
TRANSMIT BEAMFORMING : Enabled
MU-MIMO : Not-Supported
SCAN_AHEAD CHANNEL : -
ERP COEXISTENCE : ERP Protection: N Non-ERP detected: N Non-ERP associated: N
HT COEXISTENCE : HT Protection: nonmember mode, Non-HT detected: Y
Current Channel Width: 20Mhz, reason: per configuration
Num of Mcast Streams : 0 (max:25)
Multicast streams :
# MP Mcast Streams : 0
WLAN MAP :
BSS-1 : test123* (*=primary)
Shutdown WLANs :
MESHPOINT map :
BSS MAP :
BSS-1 : basic-rates = 1 2 5.5 11
: supported-rates= 1 2 5.5 6 9 11 12 18 24 36 48 54 mcs-1s mcs-2s mcs-3s
Last error :

Any ideas?

Thanks,

Aviv Kedem

[Christoph_S]

Hello Aviv,

If you insist on using only 2 antennas, I would recommend removing the antenna from R1-B, reattaching to R1-A (so you should have antennas on R1-A and R1-C only) and changing the antenna mode to 2x2.

Run the following commands either from AP profile or self:
#interface radio 1
#antenna-mode 2x2
#com wrThank you,

Chris

[Andrew_Blomley]

Your method of testing is invalid. by removing the R1-A antenna, you are effectively stopping the unit from broadcasting the SSID, the additional R1-B and R1-C do not come into play until a mobile unit is associated. This is not related to the model of an access point or even a manufacturer this is a feature of MIMO.

[Ronald_Dvorak]

How can I make it transmit trroght all of RF connectors ?

You connect a antenna on all connectors

[KK]

Hello,

rfs4k(config-profile-default-ap7562-if-radio1)# no dynamic-chain-selection

This command may solve the issue.

[Aviv_Kedem]

Hello Andrew,

I talking about t's AP7562, not AP7662.
How can I make it transmit trroght all of RF connectors ?

Thanks