Where is "RSS Threshold" or similar on the 7532 ap
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎02-23-2018 01:04 PM
Hello guys,
I would like to know where I find the "RSS Threshold" or similar on the RF domain profile of 7532 ap?
It has some document of better configurations for an environment with more than 50 7532 ap with rfs 6000 controller.
I would like to know where I find the "RSS Threshold" or similar on the RF domain profile of 7532 ap?
It has some document of better configurations for an environment with more than 50 7532 ap with rfs 6000 controller.
9 REPLIES 9
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎09-10-2019 04:26 AM
Hi Elias,
use roaming assistance policy then
VX(config)# roaming-assist-policy RSSIVX(config-roaming-assist-policy-RSSI)# handoff-threshold <-100--40> RSSI
VX(config)# wlan RSSIVX(config-wlan-RSSI)# use roaming-assist-policy RSSI Make sure though, you have some "room" for roaming overlap.
Confirm with client RF statistics
VX# show wireless client statistics rf on
Regards,
Ondrej
Hi@Ondrej Lepa
CLI: handoff-threshold <-100--40
Means the threshold of RSSI -40 to -100dbm right?. If i need signal smaller than -75dbm it is disconnected or pass to another AP with a better signal i set CLI to
VX(config-roaming-assist-policy-RSSI)# handoff-threshold <-75--40> RSSI
I'm doing right?
use roaming assistance policy then
VX(config)# roaming-assist-policy RSSIVX(config-roaming-assist-policy-RSSI)# handoff-threshold <-100--40> RSSI
VX(config)# wlan RSSIVX(config-wlan-RSSI)# use roaming-assist-policy RSSI Make sure though, you have some "room" for roaming overlap.
Confirm with client RF statistics
VX# show wireless client statistics rf on
Regards,
Ondrej
Hi
CLI: handoff-threshold <-100--40
Means the threshold of RSSI -40 to -100dbm right?. If i need signal smaller than -75dbm it is disconnected or pass to another AP with a better signal i set CLI to
VX(config-roaming-assist-policy-RSSI)# handoff-threshold <-75--40> RSSI
I'm doing right?
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎02-23-2018 01:42 PM
Hi Elias,
I bet this is something you can configure only using CLI.
Regards,
Ondrej
I bet this is something you can configure only using CLI.
Regards,
Ondrej
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎02-23-2018 01:42 PM
Hi Ondrej,
I searched the options via wegui but did not find it. Can I make these settings via wegui, or only via terminal?
I searched the options via wegui but did not find it. Can I make these settings via wegui, or only via terminal?
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎02-23-2018 01:42 PM
Hi Elias,
use roaming assistance policy then
VX(config)# roaming-assist-policy RSSI
VX(config-roaming-assist-policy-RSSI)# handoff-threshold <-100--40> RSSI
VX(config)# wlan RSSI
VX(config-wlan-RSSI)# use roaming-assist-policy RSSI
Make sure though, you have some "room" for roaming overlap.
Confirm with client RF statistics
VX# show wireless client statistics rf on
Regards,
Ondrej
use roaming assistance policy then
VX(config)# roaming-assist-policy RSSI
VX(config-roaming-assist-policy-RSSI)# handoff-threshold <-100--40> RSSI
VX(config)# wlan RSSI
VX(config-wlan-RSSI)# use roaming-assist-policy RSSI
Make sure though, you have some "room" for roaming overlap.
Confirm with client RF statistics
VX# show wireless client statistics rf on
Regards,
Ondrej
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎02-23-2018 01:13 PM
Hello Elias,
do you mean something like this?
VX# show wireless radio statistics rf on
Regards,
Ondrej
do you mean something like this?
VX# show wireless radio statistics rf on
Regards,
Ondrej