This website uses cookies. By clicking Accept, you consent to the use of cookies. Click Here to learn more about how we use cookies.
Accept
Reject
Help
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 

cli asterisk after reboot of 400-48t. Changes were saved but asterisk appears after reboot

cli asterisk after reboot of 400-48t. Changes were saved but asterisk appears after reboot

Chris3
New Contributor

‎10-02-2014 04:41 PM

Newly created stack 7.8.4 firmware with saved configuration reboots and has a * in front of CLI like it needs a save. I run save conf primary and it goes away. Run reboot command and switches (2 in stack) reboot and it comes back. my changes are still present.
I have put IP's on default vlan, set password on admin account, created another admin account
save config all.. ran out of ideas.
0 Kudos
2 REPLIES 2

Chris3
New Contributor

‎10-02-2014 05:22 PM

Thanks for your interest in this.
Here is a screenshot of the fresh reboot and sh log command. Short answer, nothing that I can see in log.

Version 7.8e.4.1 [ssh] by Build_Master on 03/18/11 03:34:35
System Serial Number: 0517G00681
Memory Size: 268435456 (256MB)!
login: gordontech
password:

Extremeware
Copyright (C) 1996-2008 Extreme Networks. All rights reserved.
Protected by U.S Patent Nos 6,678,248; 6,104,700; 6,766,482; 6,618,388; 6,034,957; 6,859,438; 6,912,592; 6,914,905; 5,694,436
=============================================================================================================================

Press the key at any time for completions.
Remember to save your configuration changes.
* 2Stack # sh log
10/02/2014 20:17:51.91 Port 2:13 link active 1000Mbs FULL duplex
10/02/2014 20:17:50.50 gordontech logged in through console
10/02/2014 20:17:44.06 Done initializing base module
10/02/2014 20:17:41.20 Start initializing base module
10/02/2014 20:17:40.08 Done initializing base module
10/02/2014 20:17:38.17 Start initializing base module
10/02/2014 20:17:37.97 Power up card 2
10/02/2014 20:17:37.87 Power up card 1
10/02/2014 20:17:34.72 Rmon Memory Allocated : 7340032
10/02/2014 20:17:34.38 SNMPv3 Engine boot count 0x99
10/02/2014 20:16:33.06 NV:Using primary config database from FLASH
10/02/2014 20:16:26.54 Memory has been allocated for gSystem
10/02/2014 20:16:01.13 System rebooted
10/02/2014 19:23:06.88 System rebooted
10/02/2014 19:12:45.23 System rebooted
10/02/2014 18:45:16.15 Login failed for user admin through console
10/02/2014 18:43:31.09 System rebooted
10/02/2014 18:26:05.60 Login failed for user admin through console
10/02/2014 18:23:15.65 System rebooted
Displayed 19 messages from memory-buffer.
* 2Stack #
0 Kudos

Paul_Russo
Extreme Employee

‎10-02-2014 05:12 PM

Hey Chris

is there anything in the log?

P
0 Kudos
GTM-P2G8KFN