Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
05-10-2019 06:57 AM
Hello,
I set up XMC with all its components (netsight, analytics, fabricmgmr and NAC) running 8.2.5.50.
I also set up a cluster of VX9000 running 5.9.4.1-004R with one AP8533 (same version).
I would like to link the VX cluster and the AP to XMC but I could not find how.
The device discovery is OK, I can see both wireless controllers in the device tab (thanks to the ZTP+ configuration), but nothing appears in Wireless -> Controllers.
I enabled "Collect device statistics" on both controllers.
What configuration am I missing ?
Thanks
I set up XMC with all its components (netsight, analytics, fabricmgmr and NAC) running 8.2.5.50.
I also set up a cluster of VX9000 running 5.9.4.1-004R with one AP8533 (same version).
I would like to link the VX cluster and the AP to XMC but I could not find how.
The device discovery is OK, I can see both wireless controllers in the device tab (thanks to the ZTP+ configuration), but nothing appears in Wireless -> Controllers.
I enabled "Collect device statistics" on both controllers.
What configuration am I missing ?
Thanks
Solved! Go to Solution.
1 ACCEPTED SOLUTION
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
05-10-2019 07:06 AM
Hi.
you need Extreme Cloud Appliance to “translate” the WiNG stats to XMC.
Most probably you will need also newer WiNG firmware.
today you can monitor your WiNG solution through snmp and FlexViews.
you need Extreme Cloud Appliance to “translate” the WiNG stats to XMC.
Most probably you will need also newer WiNG firmware.
today you can monitor your WiNG solution through snmp and FlexViews.
Regards
Zdeněk Pala
7 REPLIES 7
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-25-2022 05:58 AM
you may check this:
https://extremeportal.force.com/ExtrArticleDetail?an=000096189
Regards
Zdeněk Pala
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-13-2022 08:42 AM
the list of supported controllers for each version is published here: https://emc.extremenetworks.com/content/common/releasenotes/extended_firmware_support.htm
select version and wireless.
The Wireless Tab requires a supported controller. Please check with the local Extreme representative your options.
select version and wireless.
The Wireless Tab requires a supported controller. Please check with the local Extreme representative your options.
Regards
Zdeněk Pala
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-13-2022 08:36 AM
Hi Zdenek,
thank you. However I´m quite confused.
It´s even NOT possible, to get VX9000 into XIQ-SE (!!) Wireless Tab?
Customer does not want cloud connection....
If it is possible (in XIQ-SE), pls advise how. I just tried by myself without success
If it is NOT possible (in XIQ-SE): What CAN be "connected" to XIQ-SE Wireles Tab?
😞
thank you. However I´m quite confused.
It´s even NOT possible, to get VX9000 into XIQ-SE (!!) Wireless Tab?
Customer does not want cloud connection....
If it is possible (in XIQ-SE), pls advise how. I just tried by myself without success
If it is NOT possible (in XIQ-SE): What CAN be "connected" to XIQ-SE Wireles Tab?
😞
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-13-2022 02:32 AM
AFAIK you can connect WiNG to XIQ. You can upgrade XMC to XIQ-SE and XIQ-SE can be connected to XIQ.
The XIQ can be your single pane of glass (single glass of pain).
Attached guide can help you regarding WiNG and ExtremeControl. I hope it helps.
The XIQ can be your single pane of glass (single glass of pain).
Attached guide can help you regarding WiNG and ExtremeControl. I hope it helps.
Regards
Zdeněk Pala