- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-22-2024 05:59 AM
Hi all,
I have one AP650 and one AP630 (both Wifi6)
the 630 is connected via backhaul to the AP650 on Wifi1 (5ghz)
On cable to 650 is connected to a gigabit network, however the connected clients on 630 only get 60Mbps. the speed is super slow.
any suggestions ?
Should I change the backhaul to 2.4 ghz ?
thank you
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-27-2024 06:21 AM
Hello @mihai_balaci,
Please start here:
1 - Create a new 5GHZ radio profile and don't use the default one
2 - Disable client access on this radio for now and only enable backhaul
3 - Configure the channel manually on both APs (as an override) selecting channel 149 and above
4 - Enable OFDMA in both directions
5 - Enable DFS channels and change channel width to 40MHz
6 - Disable Frame burst
7 - Make sure you have line of sight between the 2 APs and no obstacles at all
8 - Make sure that both APs are on the same firmware version
Run this command on both APs: #show acsp neighbor
You should see the Backhaul neighbor with the VHM name, check the RSSI to see how low it is.
Test to see if this improves throughput,
BR,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-29-2024 06:24 AM
thank you.
got it
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-28-2024 09:03 AM
thank you for replying to my issue
1. done
2. I'm not sure I follow this: wifi1 has multiple intefaces (1.0,1.1,1.2) backhaul uses wifi1.2 - i still need a 5ghz network for clients
3. done
4. what is OFDMA ? how can I enable this?
5. done
6. done
7. done
8. done - both on the same fw
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-27-2024 06:21 AM
Hello @mihai_balaci,
Please start here:
1 - Create a new 5GHZ radio profile and don't use the default one
2 - Disable client access on this radio for now and only enable backhaul
3 - Configure the channel manually on both APs (as an override) selecting channel 149 and above
4 - Enable OFDMA in both directions
5 - Enable DFS channels and change channel width to 40MHz
6 - Disable Frame burst
7 - Make sure you have line of sight between the 2 APs and no obstacles at all
8 - Make sure that both APs are on the same firmware version
Run this command on both APs: #show acsp neighbor
You should see the Backhaul neighbor with the VHM name, check the RSSI to see how low it is.
Test to see if this improves throughput,
BR,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎08-28-2024 01:34 PM - edited ‎08-28-2024 01:37 PM
thanks for the reply Christoph S
I am not able to find where I can enable OFDMA in both directions and disable Frame burst.
all the rest is set.
thank you