This website uses cookies. By clicking Accept, you consent to the use of cookies. Click Here to learn more about how we use cookies.
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Extreme Networks
- Community List
- Switching & Routing
- ExtremeSwitching (EXOS/Switch Engine)
- Configure Traps for OSPF Neighbor Change on a XOS ...
Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
Configure Traps for OSPF Neighbor Change on a XOS Switch
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
12-17-2018 03:29 PM
Hello,
how can i configure a trap for an ospf neighbor change?
Mib-View is added:
#configure snmpv3 add mib-view "All" subtree 1.0/00 type included
Other traps were reached by Netsight.
Thanks,
Alex
how can i configure a trap for an ospf neighbor change?
Mib-View is added:
#configure snmpv3 add mib-view "All" subtree 1.0/00 type included
Other traps were reached by Netsight.
Thanks,
Alex
Solved! Go to Solution.
1 ACCEPTED SOLUTION
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-11-2019 12:29 PM
It worked!
The command:
Enable snmp traps ospf all
on the switch paired with the netsight alarms configuration in my last posts screen shots did work. Around 1:12 am last night there was a small interruption in one of our WAN providers, which does happen from time to time in those AM overnight maintenance windows. I received 4 emails from Netsight stating ospf neighbor state change along with the IP endpoints, all of which are on that provider. Now I remoted in and traceroutes look normal so it must have been a quick maintenance item done by the ISP.
The command:
Enable snmp traps ospf all
on the switch paired with the netsight alarms configuration in my last posts screen shots did work. Around 1:12 am last night there was a small interruption in one of our WAN providers, which does happen from time to time in those AM overnight maintenance windows. I received 4 emails from Netsight stating ospf neighbor state change along with the IP endpoints, all of which are on that provider. Now I remoted in and traceroutes look normal so it must have been a quick maintenance item done by the ISP.
10 REPLIES 10
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-08-2019 07:14 PM
I must already have it configured:
configure log filter DefaultFilter add events "ospf.neighbor.ChgState"
ERROR: Filter item you are trying to add is redundant, item not added.
sh configuration | i DefaultFilter
configure log target syslog 10.1.0.110:514 vr VR-Default local0 filter DefaultFilter severity Debug-Data
10.1.0.110 is netsight.
So in Netsight under Alarm Configuration I went to add > Selected Trap Alarm and then I added the following
OSPF Authentication Failure - ospfIfAuthFailure
OSPF Conflicting Packet - ospfIfConfigError
OSPF Interface State Change - ospfIfStateChange
OSPF Neighbor State Change - ospfNbrStateChange
All are set to send me an email. Now I wait for an actual event (or trigger one after hours) and see if I am alerted. Maybe some of those are redundant... but I'll have to see what is triggered and then maybe I can fine tune.
configure log filter DefaultFilter add events "ospf.neighbor.ChgState"
ERROR: Filter item you are trying to add is redundant, item not added.
sh configuration | i DefaultFilter
configure log target syslog 10.1.0.110:514 vr VR-Default local0 filter DefaultFilter severity Debug-Data
10.1.0.110 is netsight.
So in Netsight under Alarm Configuration I went to add > Selected Trap Alarm and then I added the following
OSPF Authentication Failure - ospfIfAuthFailure
OSPF Conflicting Packet - ospfIfConfigError
OSPF Interface State Change - ospfIfStateChange
OSPF Neighbor State Change - ospfNbrStateChange
All are set to send me an email. Now I wait for an actual event (or trigger one after hours) and see if I am alerted. Maybe some of those are redundant... but I'll have to see what is triggered and then maybe I can fine tune.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-08-2019 05:48 PM
Hello Keith,
You may configure: configure log filter CUSTOM_FILTER add event "ospf.neighbor.ChgState"
Best Regards,
Nikolay
You may configure: configure log filter CUSTOM_FILTER add event "ospf.neighbor.ChgState"
Best Regards,
Nikolay
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
01-07-2019 03:21 PM
Hi, what is the message for OSPF adjacency / neighbor change? In the article you linked you show the message is: "detect-sflow-change"
Is there a table of various messages one can trap on? I'm not in a position to break links to create a log to see what it says. I'm on a production network. I would just like to be alerted if there is a change which could indicate a particular WAN link went down.
Is there a table of various messages one can trap on? I'm not in a position to break links to create a log to see what it says. I'm on a production network. I would just like to be alerted if there is a change which could indicate a particular WAN link went down.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
12-18-2018 10:36 AM
Hello Alex,
No additional adjustment is required.
Best Regards,
Nikolay
No additional adjustment is required.
Best Regards,
Nikolay
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
12-18-2018 09:57 AM
Hi Nikolay,
thanks for your answer.
We have configured the upm profile and log event according to the gtac articel.
Do we have to additionaly adjust the snmp configuration for the trap to be send to the netsight? (We already configured the switch to send "normal" snmp traps to the netsight)
Thanks,
Alex
thanks for your answer.
We have configured the upm profile and log event according to the gtac articel.
Do we have to additionaly adjust the snmp configuration for the trap to be send to the netsight? (We already configured the switch to send "normal" snmp traps to the netsight)
Thanks,
Alex
