cancel
Showing results for 
Search instead for 
Did you mean: 

Convert csico switch voice and data configuration to Extreme X440-G2

Convert csico switch voice and data configuration to Extreme X440-G2

Rod_Robertson
New Contributor III

Current Cisco Configuration

Interface FastEthernet0/1

Description data & Phone

Switchport access vlan 60

switch mode access

swicthport voice vlan 888

spanning tree portfast

 

I have configured the extreme for voice to be tagged and data to be untagged.

When the phones connect they are connecting on teh data vlan and not voice .. so if I look at teh fdb for the port I have both macs on the data vlan ,,, incidently the phone actually works ..

LLDP is enabled,

configure lldp port 1:6 advertise system-name
configure lldp port 1:6 advertise vendor-specific dot1 vlan-name vlan VOICE-1

configure lldp port 1:6 advertise vendor-specific med capabilities
configure lldp port 1:6 advertose vendor specific power-via-mdi
confgure  lldp port 1:6 advertise vendor-specific med policy application voice vlan VOICE dscp 46

With this configuration , the Polycom phones still boot onto the data vlan ..

 

HAve I missed anything ?

Doi I need to modify the dhcp options on teh DAta vlan ..

 

1 ACCEPTED SOLUTION

Rod_Robertson
New Contributor III

Hi , thanks for all the advice , in teh end teh customer was moving to “ soft phone” so the issue with the polycom phones went away .. they were definatly both untagged so teh only way I could have supported this configuration was in effect changing teh ethernet type , for one of the vlans, then I understand you can have multiple untagged vlans on same port .. so thanks for your advice and help

 

View solution in original post

10 REPLIES 10

Miguel-Angel_RO
Valued Contributor II

Rod,

This is Cisco specific but this can be done also on other equipments.

Anyway, check the lldp config as mention by Christopher and also check the config of the IP Phone to ensure that lldp is enabled. It is usually by default but I’ve seen some IP Phones with lldp disabled by default.

please attach also the output of the fllowing command:

show lldp neighbors detailed

show lldp detailed ports 1:6

Mig

CThompsonEXOS
Extreme Employee

Hi Rod,

 

Can you attach the output of the following commands:

show vlan
show conf lldp | i 1:6

Thanks,

Chris Thompson

Rod_Robertson
New Contributor III

Hi went on site again today , and first tried Christophers suggestion, that does not work , the phone do not seem to understand Tag .. as If I connect as untagged in Voice then it all works as expected .

So basaically the phones work , untagged … so a cisco expertout there , what is the difference that they can run two untagged vlans on the same port , as per my original post .. or is this a cisco specific frig.. ( fix )

 

Thanks so far for your help

 

Miguel-Angel_RO
Valued Contributor II

Rod,

In your config you mention VOICE and VOICE-1, I think it should twice the same

Check if you polycom firmwares supports the LLDP-MED and double check the release notes. I’ve experienced some issues with old firmwares and LLDP-MED.

 

I use this with the voice VLAN tagged and the data VLAN untagged:

configure lldp port 1 advertise port-description

configure lldp port 1 advertise system-capabilities

configure lldp port 1 advertise management-address

configure lldp port 1 advertise vendor-specific med capabilities

configure lldp port 1 advertise vendor-specific med power-via-mdi

configure lldp port 1 advertise vendor-specific med policy application voice vlan VLAN200 dscp 46
 

Mig

CThompsonEXOS
Extreme Employee

Hi Rod,

 

Can you add this to your lldp configuration as well:

configure lldp port 1:6 advertise vendor-specific dot1 port-protocol-vlan-id vlan VOICE-1

Thanks,

Chris Thompson

GTM-P2G8KFN