FA Assignment : VSP4450 -> ERS3600 : Pendeing

[Klenan]

Hello,

I’m having trouble with my configuration and was wondering if anyone could help out ASAP.

Core :

====================================================================================================
                          Fabric Attach Assignment Map
====================================================================================================
Interface  I-SID      Vlan       State      Origin
----------------------------------------------------------------------------------------------------

--------------------------------------------------------------------------------
 0 out of 0 Total Num of fabric attach assignment mappings displayed
--------------------------------------------------------------------------------

CORE:1(config)#show fa assignment 1/13

====================================================================================================
                          Fabric Attach Assignment Map
====================================================================================================
Interface  I-SID      Vlan       State      Origin
----------------------------------------------------------------------------------------------------

--------------------------------------------------------------------------------
 0 out of 0 Total Num of fabric attach assignment mappings displayed
--------------------------------------------------------------------------------

ERS Stack:

Groundflr(config)#show fa assignment

 I-SID    VLAN             Source               Status
--------  ----  -----------------------------  --------
200010    10    Proxy                          Pending
200020    20    Proxy                          Pending
200030    30    Proxy                          Pending
200040    40    Proxy                          Pending
200050    50    Proxy                          Pending
200060    60    Proxy                          Pending

Binding Count: 6

Groundflr(config)#show fa assignment

i can’t seem to figure it out and i am behind schedule...anyone please!!!!

[Klenan]

@Ludovico Stevens 

CORE:1(config)#show LLdp neighbor

==========================================================================================
                                      LLDP Neighbor
==========================================================================================

Port: 1/13      Index    : 1
                Protocol : LLDP
                ChassisId: MAC Address        f4:6e:95:08:35:01
                PortId   : IfName             1/26
                SysName  : Groundflr
                SysCap   : Br / B
                PortDescr: Unit 1 Port 26
                SysDescr : Ethernet Routing Switch 3626GTS-PWR+  HW:09       FW:6.1.0.0   SW:v6.1.1.017
                Address  : 10.10.0.20
------------------------------------------------------------------------------------------
Total Neighbors : 1
------------------------------------------------------------------------------------------
Capabilities Legend: (Supported/Enabled)
B= Bridge,    D= DOCSIS,    O= Other,     R= Repeater,
S= Station,   T= Telephone, W= WLAN,      r= Router
CORE:1(config)#
CORE:1(config)#
CORE:1(

[Ludovico_Steven]

Well, the VSP is not seeing any FA neighbour.

Does the VSP see any LLDP neighbour ? On port 1/13 ?

Is the ERS plugged in the right port ?

What are the LLDP neighbours of the ERS ?

Some troubleshooting required.

[Klenan]

@Ludovico Stevens
CORE:1(config)#show fa elements

====================================================================================================
                        Fabric Attach Discovery Elements
====================================================================================================
                         MGMT                                         ELEM ASGN
PORT   TYPE              VLAN STATE  SYSTEM ID                        AUTH AUTH
----------------------------------------------------------------------------------------------------

====================================================================================================
                      Fabric Attach Authentication Detail
====================================================================================================
       ELEM OPER                      ASGN OPER
PORT   AUTH STATUS                    AUTH STATUS
----------------------------------------------------------------------------------------------------

State Legend: (Tagging/AutoConfig)
T= Tagged,    U= Untagged,    D= Disabled,    S= Spbm,    V= Vlan,    I= Invalid

Auth Legend:
AP= Authentication Pass,  AF= Authentication Fail,
NA= Not Authenticated,  N= None

--------------------------------------------------------------------------------

0 out of 0 Total Num of fabric attach discovery elements displayed
--------------------------------------------------------------------------------

CORE:1(config)#
CORE:1(config)#

[Klenan]

thank you. i’d be on site in a few hours and show you results of that command...

[Ludovico_Steven]

ERS switches by default always use FA message authentication (unlike XOS).

In your config it looks like port 1/13 is part of MLT13 where you have:

no fa message-authentication

You should probably re-enable that.

Would help if you included the “show fa elements” command from the VSP side.