This website uses cookies. By clicking Accept, you consent to the use of cookies. Click Here to learn more about how we use cookies.
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Extreme Networks
- Community List
- Wireless
- ExtremeWireless (WiNG)
- RE: CLI to show AP's connected devices' informatio...
Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
CLI to show AP's connected devices' information
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
05-18-2022 04:58 PM
Does anyone know the CLI that shows AP's actively connected client devices' (through wifi radios and also ethernet) information, including hostname, mac address, IP address ...etc ?
I know the WebUI only shows connected Wireless Clients, but not those connected through ethernet.
Thanks!
I know the WebUI only shows connected Wireless Clients, but not those connected through ethernet.
Thanks!
Solved! Go to Solution.
1 ACCEPTED SOLUTION
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
05-20-2022 02:25 PM
Hello Oxoyoz,
The output you are looking for is not available on the Wing Controller/AP. If the controller (and/or virtual controller) is utilizing onboard DHCP server feature, from the enable prompt, the following command will provide mac address, IP address, and expiration time of the wired/wireless clients.
show ip dhcp binding
You can obtain the mac addresses of all wired/wireless clients deployed and add the mac address with a friendly name, to identify by vendor or user, via the rf-domain using the following command:
mac-name xx-xx-xx-xx-xx-xx yyyyyyyy (x represents the client mac and y represents the friendly name to be used for this mac address.
The output you are looking for is not available on the Wing Controller/AP. If the controller (and/or virtual controller) is utilizing onboard DHCP server feature, from the enable prompt, the following command will provide mac address, IP address, and expiration time of the wired/wireless clients.
show ip dhcp binding
You can obtain the mac addresses of all wired/wireless clients deployed and add the mac address with a friendly name, to identify by vendor or user, via the rf-domain using the following command:
mac-name xx-xx-xx-xx-xx-xx yyyyyyyy (x represents the client mac and y represents the friendly name to be used for this mac address.
6 REPLIES 6
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
05-19-2022 04:24 AM
show mac-address-table will show all clients and other devices on your network.
But for ethernet devices that all you can see.
BTW: With the "customize" command you can change the CLI output for some commands, e.g.:
customize hostname-column-width 18
customize show-adoption-status ap-name version config-status ip-addr adopted-by last-adoption uptime cdp-lldp-info
customize show-wireless-client hostname radio-alias radio-type ip mac vendor wlan state last-active auth enc
customize show-wireless-client-stats hostname mac rx-bytes rx-errors rx-packets rx-throughput tx-bytes tx-dropped tx-packets tx-throughput t-index
customize show-wireless-client-stats-rf hostname mac signal noise snr tx-rate rx-rate average-retry-number error-rate retry-percent q-index
E.g. sometimes is better to have the AP-name + radio instead of the radio MAC address in the CLI output...
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
05-19-2022 06:43 PM
Thanks. Tobias and Angelo.
show mac-address-table gave me the connected devices' mac address on all interfaces.
However, this command line doesn't give me other details such as IP address, vendor and state for the devices. Any command to output these values, as well?
show mac-address-table gave me the connected devices' mac address on all interfaces.
However, this command line doesn't give me other details such as IP address, vendor and state for the devices. Any command to output these values, as well?
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
05-20-2022 02:25 PM
Hello Oxoyoz,
The output you are looking for is not available on the Wing Controller/AP. If the controller (and/or virtual controller) is utilizing onboard DHCP server feature, from the enable prompt, the following command will provide mac address, IP address, and expiration time of the wired/wireless clients.
show ip dhcp binding
You can obtain the mac addresses of all wired/wireless clients deployed and add the mac address with a friendly name, to identify by vendor or user, via the rf-domain using the following command:
mac-name xx-xx-xx-xx-xx-xx yyyyyyyy (x represents the client mac and y represents the friendly name to be used for this mac address.
The output you are looking for is not available on the Wing Controller/AP. If the controller (and/or virtual controller) is utilizing onboard DHCP server feature, from the enable prompt, the following command will provide mac address, IP address, and expiration time of the wired/wireless clients.
show ip dhcp binding
You can obtain the mac addresses of all wired/wireless clients deployed and add the mac address with a friendly name, to identify by vendor or user, via the rf-domain using the following command:
mac-name xx-xx-xx-xx-xx-xx yyyyyyyy (x represents the client mac and y represents the friendly name to be used for this mac address.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
05-20-2022 04:36 PM
Thanks. Christopher.
show ip dhcp binding worked
show ip dhcp binding worked
