Extreme Networks

ar1 · 08-13-2019

Hello, we are using XMC and NAC version 8.2.6.5 at VMWare and from time to time I see that the time is wrong (2h in the future). If I check the output of "systemctl status ntp.service" I see that the service ist exited: root@xmc.test.net:~$ systemctl...

ar1 · 12-14-2018

Hello, we use MAC and 802.1X authentication with EXOS and EOS switches and sometimes I need to delete a netlogin / multiauth session on a switchport via cli example: the "show netlogin session ports" or "show multiauth session ports" showes me an en...

ar1 · 11-02-2018

Hi all, I have a problem to become my AP3915i active on a V2110 Conroller in a different VLAN. I have configured DHCP Option 78 and I can ping the AP from the Controller MGMT_Plane_Interface and from the AP I can Ping the controller. After connecting...

ar1 · 10-04-2018

Hi all, we have many switches (EOS and EXOS) and I would like to know if my design is OK or how to make it better. We have switches in our DMZ but most of them in our LAN behind Internet and DMZ firewall. All switches will be managed by a single sep...

ar1 · 06-20-2018

Hello, I have the following problem: I have a managed 4 Port-Noname-Switch attached at a switch G3G124-24 at port ge.1.4. The managed 4-Port-Switch is manageable and has its own IP-Address and should be reachable via VLAN ID 400 but tagged. The G3G12...

ar1 · 10-18-2023

Hi,the error message looks like that you shoud not ud .pol:> Slot-1 SW1.2 # configure ssh2 access-profile My_SSH_Policy.pol> Error: Policy /config/My_SSH_Policy.pol.pol does not exist on file system> Configuration failed on backup Node, command execu...

ar1 · 08-28-2019

Hi Zdenek, I have checked time and timezone settings many times. I have found out that the problem has something to to with the open-vmware-tools because since I have stoped them (systemctl stop open-vm-tools.service) the time is correct. I will chec...

ar1 · 08-22-2019

Hi Robert, I guess you shouldn't power off the chassis because if you switch it on again I'm not sure that the configured and running fabric modul will be the the master. In the past I had a defective module in a S8-Bond-System and I did't power th...

ar1 · 08-22-2019

Hi Robert,, I would suggest to update the firmware at the new module first (but in most cases the other fabric moduls will do this, too). I didn't know if there is a procedure for such replacement but I would first save the configuration and shutdown...

ar1 · 07-24-2019

Hi Alex, that's sounds strange: You can send and receive files from a windows tftp client to/from the Linux server You can send and receive files from the switch to/from the Windows server but You cannot send/receive files to/from the Linux server ...

Extreme Networks

User Statistics

User Activity

ntp shows wrong time on XMC and NAC-Gateway

Is it possible to delete a netlogin / multiauth session an a port via cli?

AP3915i will not become active but communicate with controller

Design Question: should I use MGMT port or better not?

Question about VLAN Egress Priority at Switches (G3G and C5K, stativc vers. assign by auth))

Re: Issue with SSH ACL policy on older switch models

Re: ntp shows wrong time on XMC and NAC-Gateway

Re: SK8008-1224-F8 fabric module replacement on bonded S4 chassis

Re: SK8008-1224-F8 fabric module replacement on bonded S4 chassis

Re: TFTP / Solution for a linux server