X440 and Netsight Nac The session is no longer active due to: Admin-Reset.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎07-22-2016 07:24 AM
Hello all
i have the following Problem with one Device in our Network
It is an CAB Label Printer connected on an X440 with Netsight
After 10 Minutes the following message is in the Netsight Nac manager
The session is no longer active due to: Admin-Reset.
If the message appear in the NAC the Device is no longer reachable
only Force Reauth and Power off the Device brings it back
Is anbody here that have an idea was it is
regards
Oliver
i have the following Problem with one Device in our Network
It is an CAB Label Printer connected on an X440 with Netsight
After 10 Minutes the following message is in the Netsight Nac manager
The session is no longer active due to: Admin-Reset.
If the message appear in the NAC the Device is no longer reachable
only Force Reauth and Power off the Device brings it back
Is anbody here that have an idea was it is
regards
Oliver
13 REPLIES 13
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎03-14-2019 10:29 AM
Any news about that specific issue? It seems i ran into the exact same issue with firmware version 30.1.1.4. After disabling radius-accounting, i did not have the issue described...
Regards
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎03-25-2019 07:47 AM
Hi Philipp,
i would not use 30.1 for productive environmemts - wait 2 months for 30.2.
i would suggest 22.6 Patch 1-1 and if the issue is reproduceable - open a GTAC Case that Extreme Engineering can fix this issue.
BR,
Matthias
i would not use 30.1 for productive environmemts - wait 2 months for 30.2.
i would suggest 22.6 Patch 1-1 and if the issue is reproduceable - open a GTAC Case that Extreme Engineering can fix this issue.
BR,
Matthias
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎05-05-2017 05:50 AM
Current state of the issue is:
It occurs if RADIUS Accouting AND dynamic Session-ReAuth (provide by RADIUS Session-Timout Value) run simultaniously. Disable one of both, the problem disappears.
I hope we can find the root cause because both feature needed.
Regards
It occurs if RADIUS Accouting AND dynamic Session-ReAuth (provide by RADIUS Session-Timout Value) run simultaniously. Disable one of both, the problem disappears.
I hope we can find the root cause because both feature needed.
Regards
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Report Inappropriate Content
‎05-05-2017 05:50 AM
Fighting with the same problem:
Windows 7 / 802.1x / X440-G2 EXOS V21.1.3.7-Patch1-4 with Extreme Control V7.1.1.9
05/05/2017 08:24:17.07 Slot-1: The authentication state of Network Login user host/YLQP019998.XXX.xx was cleared by policy due to Admin Reset, Mac 90:1B:0E:2E:35:5C port 2:26 VLAN(s) "" Protocol(s) "802.1x"
What is reason "Admin Reset" - either Re-Auth Button in NAC was pressed nor clear netlogin session per CLI was used. It happens randomly!
How is it possible to get EAPoL Counters regarding this port to verify if EAPoL Logoff Messages was sent from Client ?
Regards
Windows 7 / 802.1x / X440-G2 EXOS V21.1.3.7-Patch1-4 with Extreme Control V7.1.1.9
05/05/2017 08:24:17.07 Slot-1: The authentication state of Network Login user host/YLQP019998.XXX.xx was cleared by policy due to Admin Reset, Mac 90:1B:0E:2E:35:5C port 2:26 VLAN(s) "" Protocol(s) "802.1x"
What is reason "Admin Reset" - either Re-Auth Button in NAC was pressed nor clear netlogin session per CLI was used. It happens randomly!
How is it possible to get EAPoL Counters regarding this port to verify if EAPoL Logoff Messages was sent from Client ?
Regards