cancel
Showing results for 
Search instead for 
Did you mean: 

The ap's ip address is incorrect on adoption status result.

The ap's ip address is incorrect on adoption status result.

zlinuxboy
Contributor

I deploy 3 AP7522s, one of them is VC. here is the context of profile ap7522 default-ap7522

profile ap7522 default-ap7522
use enterprise-ui
ip name-server 221.176.88.95
ip default-gateway 192.168.9.254
autoinstall configuration
autoinstall firmware
use radius-server-policy WERSP
crypto ikev1 policy ikev1-default
isakmp-proposal default encryption aes-256 group 2 hash sha
crypto ikev2 policy ikev2-default
isakmp-proposal default encryption aes-256 group 2 hash sha
crypto ipsec transform-set default esp-aes-256 esp-sha-hmac
crypto ikev1 remote-vpn
crypto ikev2 remote-vpn
crypto auto-ipsec-secure
crypto load-management
crypto remote-vpn-client
interface radio1
data-rates gn
wlan wing-hkxd bss 1 primary
interface radio2
wlan wing-hkxd bss 1 primary
interface ge1
switchport mode trunk
switchport trunk allowed vlan 7-10
switchport trunk native vlan 9
interface vlan1
ip address dhcp
ip address zeroconf secondary
ip dhcp client request options all
interface pppoe1
use firewall-policy default
ntp server 0.pool.ntp.org
use client-identity-group default
virtual-controller auto
virtual-controller management-interface ip address 192.168.9.140/24
virtual-controller management-interface vlan 9
rf-domain-manager capable
logging on
service pm sys-restart
router ospf
adoption-mode controller
!
rf-domain default
timezone Asia/Shanghai
country-code cn
use smart-rf-policy hkxd
use nsight-policy default
!
ap7522 74-67-F7-04-31-5C
use profile default-ap7522
use rf-domain default
hostname ap7522-04315C
interface vlan9
ip address 192.168.9.143/24
!
ap7522 74-67-F7-04-4F-A8
use profile default-ap7522
use rf-domain default
hostname cz3-ap46
!
ap7522 74-67-F7-04-4F-C4
use profile default-ap7522
use rf-domain default
hostname ap7522-044FC4
!
ap7522 74-67-F7-04-53-20
use profile default-ap7522
use rf-domain default
hostname ap7522-045320
interface vlan9
ip address 192.168.9.144/24
!
ap7522 74-67-F7-A1-AE-58
use profile default-ap7522
use rf-domain default
hostname ap7522-A1AE58
interface vlan9
ip address 192.168.9.142/24
!
ap7522 74-67-F7-A2-DA-54
use profile default-ap7522
use rf-domain default
hostname ap7522-A2DA54
interface vlan9
ip address 192.168.9.141/24
no adoption-mode

the VC’s IP is 192.168.9.140

the 3 AP’s mac and IP are:

74-67-F7-04-31-5C : 192.168.9.143

74-67-F7-04-53-20 : 192.168.9.144

74-67-F7-A2-DA-54 : 192.168.9.141

but when `show adoption status` on vc

ap7522-04315C> show adoption status
Adoption Mode: CONTROLLER
--------------------------------------------------------------------------------------------------------------------------------
DEVICE-NAME VERSION CFG-STAT MSGS ADOPTED-BY LAST-ADOPTION UPTIME IPv4-ADDRESS
--------------------------------------------------------------------------------------------------------------------------------
ap7522-045320 5.9.8.4-002R configured No ap7522-04315C 0 days 00:18:52 0 days 00:21:01 192.168.9.140
ap7522-A2DA54 5.9.8.4-002R configured No ap7522-04315C 0 days 00:30:23 0 days 15:23:04 192.168.9.141
---------------------------------------------------------------------------------------------------------------------------------

The ap7522-045320’s IP was change from 9.144 to 9.140(VC), what is wrong?

 

Question2:

I serial console to ap7522-045320, the hostname have a suffix ‘*’:

ap7522-045320*#

what does it mean?

1 ACCEPTED SOLUTION

ckelly
Extreme Employee

Okay, that makes more sense then.

So in the neighbor output from 04315C, we can see its two neighbors.

So 04315C has a level-1 MINT link to each of these APs, as expected.

This is what I would expect to see.

View solution in original post

15 REPLIES 15

ckelly
Extreme Employee

Okay...so the output from the VC, as you did, should look like your original posting - with the two APs listed.

Try running the neighbor command on each AP.  Each one should list the other 2 APs.

 

zlinuxboy
Contributor

@Chris Kelly hold on man, I just update the last comment, pls check it out again.

ckelly
Extreme Employee

Okay, that makes more sense then.

So in the neighbor output from 04315C, we can see its two neighbors.

So 04315C has a level-1 MINT link to each of these APs, as expected.

This is what I would expect to see.

zlinuxboy
Contributor

Sorry, I have cut down the APs number from 6 to 3eb96890828b84221b499c9429be8dc05_263a.png , I should put the sentence ”I have 3 AP7522 and deploy as dynamic VC scene ”  at first of the last post.

here is the result of `show mint neighbors` on vc:

ap7522-04315C>show mint neighbors
2 mint neighbors of 75.04.31.5C:
75.04.53.20 (ap7522-045320) at level 1, best adjacency vlan-9
75.A2.DA.54 (ap7522-A2DA54) at level 1, best adjacency vlan-9

does this links number correct? It’s only 1 link to neighbors

ap7522-04315C>show mint links
1 mint links on 75.04.31.5C:
link vlan-9 at level 1, 2 adjacencies, DIS 75.04.53.20

based on you comment, isn’t it should be 2 links to the other neighbors?

GTM-P2G8KFN